


JBL T450BT
Introducing JBL T450BT on-ear wireless headphones. They’re flat-folding, lightweight, comfortable and compact. Under the hood, a pair of 32mm drivers punch out some serious bass, reproducing the powerful JBL Pure Bass sound you’ve experienced in much bigger venues. Music and call controls/microphone are placed on the earcup. And because your music should go where you go, you’ll get up to 11 hours of uninterrupted audio playback on a single charge.
Product Specifications
General Specifications
Driver size (mm) | 32.0 |
---|
Audio Specifications
Dynamic frequency response range (Hz) | 20 Hz - 20 kHz |
---|---|
Impedance (ohms) | 32.0 |
Number of drivers per ear | 1.0 |
Dimension Specifications
Weight (g) | 320 |
---|---|
Weight (oz) | 11,29 |
Control Connect Specifications
Bluetooth profiles | HFP v1.5, HSP v1.2, A2DP v1.2, AVRCP v1.4 |
---|---|
Bluetooth frequency | 2.402GHz-2.48GHz |
Bluetooth transmitted modulation | GFSK,π/4DQPSK, 8DPSK |
Bluetooth transmitter power | 0-4 dbm |
Bluetooth version | 4.0 |
Documents & Downloads
Spec Sheets
Quick Start Guide
What’s in the Box
- 1 x Pair of JBL T450BT headphones
- 1 x Charging cable
- 1 x Quick start guide
- 1 x Warning Card
- 1 x Warranty Card
- 1 x Safety Sheet

FAQs & How-Tos
How can I reset my JBL headphones?
With the headphones switched ON, press and hold the Volume + and Volume - buttons for more than 5 seconds.
The LED blinks two colors, and now you have reset to factory settings.
Was this helpful?
Thank you for your feedback!
How Do I connect my T450BT via Bluetooth?
In normal use, T450BT pairing mode is automatic.
First time it is switched on, it goes into pairing mode at once, shown by the blue LED blinking.
After first pairing, if the last used source is not on when the T450BT is switched on, it will wait about 10 seconds with the LED showing white light, then it will switch to pairing mode, with the LED turning blue, and blinking.
If you want to start pairing mode manually, make sure that the headphones are switched off, then press and hold the on/off button for more than 5 seconds.
The headphones will now switch on in pairing mode, shown by the blue LED blinking.
Was this helpful?
Thank you for your feedback!
Can I replace the ear pads on my T-series headphone?
Yes, the ear pads are replaceable by owner.
The pads can be purchased as spare parts from the service center, or purchased directly from the JBL spare parts web shop, when opened.
Was this helpful?
Thank you for your feedback!
How many devices can I pair my T450 headphones to?
They support up to 8 paired devices without reset.
Was this helpful?
Thank you for your feedback!
How can I see that my T450BT is fully charged?
The charging LED stops lighting white, and goes dark.
Was this helpful?
Thank you for your feedback!
Can the JBL T450BT be used with a cable?
No, this is a Bluetooth only headphone.
Charging is done with cable, of course, but there is no cabled audio connection.
Was this helpful?
Thank you for your feedback!
Waterproof Information
This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.
Was this helpful?
Thank you for your feedback!
aptX Audio Codec Support
This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.
Was this helpful?
Thank you for your feedback!
Can the JBL T450BT be charged while listening to music?
No, as soon as charging begins, the headphone shuts down.
Since no option for cabled listening exists for this model, it is necessary to charge before listening is again possible.
Was this helpful?
Thank you for your feedback!