How To

Support Overview / How To

How To

448 results

Sort

Page size

How to Turn off your TWS Headphones

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

Was this helpful? Thank you for your feedback!
How to switch between Game and Chat balance

Yes, you can adjust the game and chat audio balance by rotating the dial-up and down. When you rotate the dial, you'll feel a notch that indicates the balance is 50% game and 50% chat. The slider on Quantum ONE is different and has no notch but instead a visual indicator.

Was this helpful? Thank you for your feedback!
How to switch between Active Noise Cancelling and TalkThru

Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.

Was this helpful? Thank you for your feedback!
How to show the current software version
To show the current firmware version on your JBL TUNER device, go through the following steps.
1. Turn on the JBL TUNER.
2. Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
3. In the display, you will see a combination of letters and numbers. This is the current software version.
4. See picture below as illustration.
The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.
Was this helpful? Thank you for your feedback!
How to set up your microphone
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select Sound

3 Select Recording

4. Make sure to select the proper recording device.
1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"
5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Chose Levels and adjust accordingly
Was this helpful? Thank you for your feedback!
How to set up your microphone
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

Check that the PC is using the correct recording device.

1. Go to Control Panel

2. Select Sound

3 Select Recording

4. Make sure to select the proper recording device.
1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or "Select Default Communication Device"
5. Check the microphone levels by right-click on your Quantum headset.

6. Go to Properties

7. Choose Levels and adjust accordingly
Was this helpful? Thank you for your feedback!
How to set up your microphone
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.

How to check your PC settings for the correct recording device
1. Go to Control Panel

2. Select Hardware and Sound

3. Click on Sound

3 Select Recording

4. Make sure to select the proper recording device.
1. Right-click on it Quantum headset.
2. Now select "Set Default Device" or Select "Default Communication Device"
5. Check the microphone levels by right-click on your Quantum headset. Then click on Properties

6. Choose Levels.

7. Adjust accordingly.

Please also make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume.
Check that your headset's Game-Chat balance dial and ensure that the balance is correct, you might refer to the screenshot below from the QuantumEngine PC software.

If you still cannot hear the game or music audio, or if the volume is still very low, check if the TalkThrough is activated via the QuantumEngine software.

Finally, you can also do a short press on the Smart Ambient button on the headset (if your headset, has this feature)
Was this helpful? Thank you for your feedback!
How to set up your device with Android or iOS
1. Power on your JBL LINK speaker.
2. Verify that you are connected to the right Wi-Fi network on your smartphone.
3. Open your Google Home app .
4. Enable Bluetooth
5. Enable Location Service (Android Only)
  1. Make sure you have permitted the Google Home app to view your location.
6. First option Tap Add Set up device Set up new devices in your home
7. Second option Tap X device found Select Home location
8. Follow the instruction on screen to add your new JBL LINK speaker.
You are now all set and can enjoy your LINK device!
Was this helpful? Thank you for your feedback!
How to save your favorite music to the My Moments feature

(1) Use JBL One App to set up the My Moment Feature.
(2) Select the JBL soundbar you want to set your favorite music to the My Moment feature.
(3) Tap the My Moment card to assign music.
(4) Click Add Music to manage music streaming services and specific music tracks.
(5) Set the timer to inactive speaker/soundbar (optional)
(6) Set the music loudness (optional)
(7) Press SAVE

Was this helpful? Thank you for your feedback!
How to restore factory default settings on your device
With our JBL BAR 5.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings.

Let us walk through each one of them.

Resetting WiFi settings
1. Turn on your JBL BAR 5.1 Surround.
2. Press and hold POWER button down for more than 10 seconds.
3. All of your WiFi configuration is lost and you need to reinstall it again.
Use the Google Home app to install the device on your WiFi network.

Resetting to Factory default settings
1. Turn on your JBL BAR 5.1 Surround
2. Press and hold POWER and SOURCE button for 3 seconds.
3. Your device is now reset.
You can now start allover with installing your BAR 5.1 Surround.
Was this helpful? Thank you for your feedback!
How to restore factory default settings on your device

With our JBL BAR 9.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings. Let us walk through each one of them. Resetting WiFi settings Turn on your JBL BAR 9.1 Surround. Press and hold POWER button down for more than 10 seconds. All of your WiFi configuration is lost and you need to reinstall it again. Use the Google Home app to install the device on your WiFi network. Resetting to Factory default settings Turn on your JBL BAR 9.1 Surround Press and hold POWER and SOURCE button for 3 seconds. Your device is now reset. You can now start allover with installing your BAR 9.1 Surround.

Was this helpful? Thank you for your feedback!
How to restore factory default settings (factory reset) for your device
The factory reset button restores your device to the default settings, including network and audio configurations.

Please use one of the following solutions:
1. Press and hold VOL -, VOL +, and Source buttons on the device at the same time until the LED light flashes (hold for more than 5 seconds)
Or alternatively;
1. Open your JBL ONE App.
2. Navigate to the support tile.
3. Select RESTORE FACTORY SETTINGS.
Was this helpful? Thank you for your feedback!