JBL PartyBox On-The-Go
|Output power (W)||100|
|Dynamic frequency response range (Hz)||50 Hz - 20 KHz (-6 dB)|
|Dimensions (in)||23.62 x 14.45x 12.36|
|Dimensions (cm)||60 x 36.7 x 31.2|
Control Connect Specifications
|Bluetooth profiles||A2DP 1.3, AVRCP 1.6|
|Bluetooth frequency||2.4 – 2.48GHz|
|Bluetooth transmitted modulation||GFSK, π/4 DQPSK, 8DPSK|
|Bluetooth transmitter power||10 dBm (EIRP)|
Documents & Downloads
Quick Start Guide
What’s in the Box
- 1 x JBL PartyBox On-The-Go
- 1 x wireless microphone*
- 1 x Power cable - relevant to SKU matrix
- 1 x Quick-start guide
- 1 x Safety sheet
- 1 x Warranty sheet
- * Asia Pacific countries, except India and Japan, contain 2x wireless microphone in the box.
FAQs & How-Tos
- Press the Play and Boost button at the same time for 5 seconds.
- Depending on what state your JBL Partybox is in, either you enter Demo mode or disabling it.
- NOTE: In Demo mode, you cannot use the JBL Partybox as most features and buttons are not working.
Resetting the Partybox to Factory Settings
- Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
- The JBL Partybox will power off and back on and is now reset.
Connecting a USB stick
- You can enjoy music from your USB Stick directly into the Partybox device.
- Insert the Stick into theport, located on the back of your Partybox.
- The USB Stick has to be formatted FAT16 or FAT 32 and supports MP3, WAVE and WMA Music files.
- It will start automatically playing the content on your USB stick.
- You can connect any devices through the analog connection
- Use an analog cable (Not included in the box) and connect your device.
- Press play on your external device and enjoy the music!
RCA Connection (*Partybox 200/300/1000 Only)
- The Partybox features both Input and Output RCA connection.
- Connect your RCA cable (not included) to either one of the ports.
- You can use it with your DVD/BlueRay player or AVR system.
Guitar and Microphone
- Connect your to the dedicated port or connect your electric to the
- You can mix sound or make your own karaoke party with your Partybox.
- Sing or play through your devices.
- To adjust the volume of the audio source, press volume+ or volume- buttons.
- To adjust the volume of the microphone or guitar, rotate the or
Charging external devices
- Whenever your mobile device needs some extra power, the Partybox can help you!
- Featuring a USB Charging port for both Music (USB on a stick) or when you need to charge your device.
- Simply connect your device to the port and start charging.
- NOTE: The Partybox 200 needs to be connected to AC power all the time to charge or function as a speaker.
- The Party 300/310 has a battery and can charge any device without needing AC power (unless the product's battery is depleted then you need to recharge via AC power).
There are many ways to enjoy your JBL Partybox On-The-Go, 100, 200, 300, 310 & 1000. The options are endless and you are in control of the party
- Get an empty stick with speed of 2.0.
- Make sure it is formatted with FAT16 or FAT32.
- Your Music files can only be: (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
- The Partybox supports up to 8 subfolders.
- It will be played in alphabetic sequence with main folders first then subfolders.
- To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.
When a wireless mic is connected, the speaker will play a notification sound once. If two wireless mics are connected at the same time, there may be a 1 sec gap between the two notification sounds.
If one of the wireless mics is not working, we recommend the following:
1. Turn off the speaker
2. Turn on the mic and place it on top of the speaker
3. Turn on the speaker
4. The speaker should automatically pair with the new mic within 3 min and play a notification sound
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).
TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.
Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 and PartyBox 300 which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the Partybox 110, 310, 710 or Encore/Essential together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.
- Press the button on the Partybox to start the pairing process.
- Grab your device.
- Go to settings --> Bluetooth --> Enable Bluetooth -->
- Find the Partybox speaker you want to establish a Bluetooth connection to.
- You now have a successful connection and can stream your favorite music.
- NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
- To stop Bluetooth broadcasting then insert a USB device.