JBL PartyBox 300
Portable Bluetooth party speaker with light effects
Sold from 2019 until now
Getting started with your JBL PartyBox 300
Documents & Downloads
Product Specifications
- Output power (W)
- 240
- Dynamic frequency response range (Hz)
- 45Hz-20kHz
- Dimensions (cm)
- 31 x 69 x 32
- Dimensions (in)
- 12.2 x 27.2 x 12.6
- Weight (kgs)
- 15.84
- Weight (lbs)
- 34.9
- Bluetooth profiles
- A2DP V1.3, AVRCP V1.6
- Bluetooth frequency
- 45Hz-20kHz
- Charging time (hrs)
- 5
- Maximum music playing time (hrs)
- 18
- 3.5 mm audio cable Input
- Yes
- Bluetooth
- Yes
- Charging cable
- Yes
- Lightshow
- Yes
- Powerbank
- Yes
- Wireless
- Yes
- JBL Signature Sound
- Yes
- Rechargable battery
- Yes
- Note
- The product is in compliance with the European Union energy legislation. 1) Bluetooth connection mode - The product is intended to be used for streaming music via Bluetooth connection. A consumer can stream Bluetooth audio to the speaker. When the product is connected through Bluetooth, the Bluetooth connection must remain active at all times to ensure proper operation. The product will enter into sleep mode (networked standby), after 20 minutes without operation, the power consumption @ sleep is less than 2.0 Watts, after which it can be re-activated via Bluetooth connection. 2) Bluetooth disconnection mode - The product will enter into standby mode, after 20 minutes without operation, the power consumption @ standby is less than 0.5 Watts.
Be Loud, Be Proud, Be Ready To Party!
The JBL PartyBox 300 is a powerful party speaker with JBL sound quality and vivid light effects. Thanks to its rechargeable battery and 12V DC input you can bring the party everywhere. Just plug in your Mic or Guitar and take the stage or stream your playlist via Bluetooth or from a USB stick. Connect two PartyBox speakers wirelessly with the TWS feature or wired from one RCA output to another RCA input. Let's get the party started!
Enjoy an immersive audio experience at home or at a party that only JBL sound can provide.
There's a light mode for every mood: Meter, Pulse and Party mode.
Plug in to the 12V DC output of your car or use the built-in 10,000mAh battery for up to 18 hours of playtime.
Plug in your mic or guitar and take the stage.
Wirelessly stream high-quality sound from your smartphone or tablet.
Pre-program your party or event with your favorite playlist from a USB thumb drive!
Connect compatible speakers wirelelessly via TWS (True Wireless Stereo using Bluetooth connection up to 2 party speakers) or wired via one RCA outpur to another.
A USB port on the JBL PartyBox lets you charge other USB devices right from the speaker. So you don’t need an extra charger to keep your devices powered up.
FAQs & How-Tos
12 results
-
It is very simple to connect to your Car with the JBL Partybox 200 or 300. Use the included cable that connects through the cigarette connector in your Car and power on the Partybox! Please note that the 12V connection does not charge the battery in the Partybox 300 - it will only power the Partybox when in use. To charge the battery, it will have to be plugged into AC power ( 110 - 230V )Was this helpful? Thank you for your feedback!
-
Demo mode
- Press the Play and Boost button at the same time for 5 seconds.
- Depending on what state your JBL Partybox is in, either you enter Demo mode or disabling it.
- NOTE: In Demo mode, you cannot use the JBL Partybox as most features and buttons are not working.
Was this helpful? Thank you for your feedback! -
To control the Light show on your JBL Partybox device, simply press the dedicated "Light show" button located under the Bluetooth icon. There are 3 different light shows available when toggling through them, select your favorite one and have a blast. There is no app developed to control or modify these settings, all settings have to be done on the Partybox device.Was this helpful? Thank you for your feedback!
-
Bluetooth Pairing
- Press the button on the Partybox to start the pairing process.
- Grab your device.
- Go to settings --> Bluetooth --> Enable Bluetooth -->
- Find the Partybox speaker you want to establish a Bluetooth connection to.
- You now have a successful connection and can stream your favorite music.
- NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
- To stop Bluetooth broadcasting then insert a USB device.
Was this helpful? Thank you for your feedback! -
Finding the software version
- Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
- A voice will start prompting numbers which indicates the current software version.
Was this helpful? Thank you for your feedback! -
USB Stick
- Get an empty stick with speed of 2.0.
- Make sure it is formatted with FAT16 or FAT32.
- Your Music files can only be: (32-320kbit/s), (32-320kbit/s) and (44.1K/48K/192K).
- The Partybox supports up to 8 subfolders.
- It will be played in alphabetic sequence with main folders first then subfolders.
- To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.
Was this helpful? Thank you for your feedback! -
Resetting the Partybox to Factory Settings
- Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
- The JBL Partybox will power off and back on and is now reset.
Was this helpful? Thank you for your feedback! -
This model is not supported by the JBL Partybox App.Was this helpful? Thank you for your feedback!
-
It is possible to pair two of the same model of JBL PartyBox speakers together through TWS (True Wireless Stereo) mode.
PartyBox On-The-Go/100:
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).
PartyBox 200/300/1000:
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.
Partybox 110/310/710/Encore/Essential:
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).
TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.
Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 and PartyBox 300 which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the Partybox 110, 310, 710 or Encore/Essential together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.Was this helpful? Thank you for your feedback! -
You can have your own Karaoke party with your JBL Partybox. Simply connect your Microphone (only included with the Partybox On The Go) and connect your mobile device over Bluetooth, then start playing music and sing along, it is that simple!Was this helpful? Thank you for your feedback!
Images & Videos
Can’t find what you’re looking for?
Chat with Us
Mon - Fri - 10:00 a.m 7:00 p.m (NZST)