How To
How To
448 results
-
Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.Was this helpful? Thank you for your feedback!
-
The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.Was this helpful? Thank you for your feedback!
-
Select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your headphones' battery life appears in the top left corner. If you have an IOS device, you also will be able to see the battery life indicator in the upper right hand corner next to the BT symbol. Additionally, you should hear the audible voice stating ‘low battery’ when you have 15-20 minutes left of battery life left on the headphones.Was this helpful? Thank you for your feedback!
-
As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.Was this helpful? Thank you for your feedback!
-
If you cannot stream music with AirPlay, use the JBL One App;
(1) Go to Settings.
(2) Select 3rd Party Service.
(3) Select the Airplay tile.
(4) Select Reset AirPlay.Was this helpful? Thank you for your feedback! -
The Stadium GTO 20M is intended for use with the Stadium GTO two-way systems, or to replace existing midrange speakers in systems that are already three-way from the start. The Stadium GTO two-way component systems are 3-way upgradeable. The crossovers are gap-switchable to accommodate a midrange upgrade. The optional Stadium GTO 20M midrange includes a bandpass crossover to convert a two-way system into a threeway system with perfect tonal balance. You simply connect both crossovers to the speaker wires from your car amplifier in parallel, and set the existing GTO two-way crossover to GAP function. Stadium GTO 20M is designed to also fit into many factory three-way applications. Please note that you cannot use this add-on midrange with coaxial car speakers, unless you can access the crossover networks to establish the midrange gap that the extra midrange is meant to occupy.Was this helpful? Thank you for your feedback!
-
The Club 5501 is a mono amplifier for subwoofer use in cars. It can be confusing to see that it has two inputs, marked left and right, as well as two speaker output pairs. But it is still a mono amplifier, with only one channel. The two inputs are there to make it easier to connect to a normal car radio/head unit, where you will often have two normal full-range connectors, left and right. You can insert both into the 5501. However, if you only have one signal lead going to the 5501, you can use either of the inputs. They are combined into one inside the amplifier anyway. Also, the two sets of speaker connections are there to make it easier to connect two subwoofers simultaneously. The two sets are completely identical, so you can use either one for a single subwoofer, or both. If you connect two, they will be in parallel.Was this helpful? Thank you for your feedback!
-
• Plug the JBL DRG into OBD II port in your vehicle first. • Start your engine (JBL DRG will enter low power mode when the engine is off) • Then press Bluetooth button on DRG for pairing and connection to your smartphone. • After connected, launch the “JBL DRG” app on your smartphone. • Press the settings button on the left top of the app to enter the settings page. If your head unit’s Bluetooth is in discoverable mode, please enable the “Inquiry Mode” on the settings page. If your head unit’s Bluetooth is in inquiry mode, please disable “Inquiry Mode” on the settings page. • Exit the settings page and select “Bluetooth” in “Connection Mode”, JBL DRG will start the connection with head unit.Was this helpful? Thank you for your feedback!
-
• Make sure that JBL DRG is connected via Bluetooth with your smartphone and the JBL DRG” app has been launched. • Search a FM frequency band with your head unit. (an unrestricted frequency would be one that is not occupied by a radio station). • Select “FM” in “Connection Mode” on the JBL DRG App and key in the FM unrestricted frequency you have selected in the right window, JBL DRG will then transfer audio to your head unit and play through your vehicle’s audio system.Was this helpful? Thank you for your feedback!
-
Go to your Bluetooth Settings to confirm that you are connected to both JBL Reflect Fit Audio and JBL Reflect Fit HRM. Once you are connected to the Reflect Fit HRM you will hear the audio voice prompt state, "Searching for Heart Rate"......"Calibrating" followed by a heart beat prompt. It will calibrate for 2-5 seconds followed by "Heart Rate Detected". If it cannot verify your heart rate, the audio voice prompt will advise you to adjust the ear piece. Once it has established your heart rate, you will be able to manually check your heart rate by pressing the heart button located on the RIGHT arm of the neck band.Was this helpful? Thank you for your feedback!
-
The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.Was this helpful? Thank you for your feedback!
-
To answer and hang up calls, press the pause/play button located on the left arm of the Soundgear.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon - Fri - 10:00 a.m 7:00 p.m (NZST)