How To
How To
-
In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.Was this helpful? Thank you for your feedback!
-
In power ON mode press and hold the "Volume +" and "Phone" buttons at the same time for more than 3 seconds -> Unit will power Off by itself.
Now the unit is reset to factory default.
Was this helpful? Thank you for your feedback! -
Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.Was this helpful? Thank you for your feedback! -
Resetting the Partybox to Factory Settings
- Press and hold "Play" and "Light" buttons for > 10 seconds.
- The Partybox will power off and back on and is now reset.
Was this helpful? Thank you for your feedback! -
To re-establish the functionality of the Advanced Swipe Controls (details in the image below), first update the My JBL Headphones app in the Google Play/App Store.
After the installation is completed, pair the earbuds to your phone/tablet through Bluetooth and open the app.
The earbuds will be detected and displayed in the app and you should see that a Firmware update is available.
Note: Advanced touch controls are deactivated by default, in the My JBL Headphones app go to Settings
once your earbuds are displayed, then select Gestures and enable Advanced Swipe Controls. You can now select each function and assign it to a specific gesture.
Was this helpful? Thank you for your feedback! -
(1) On the subwoofer's rear panel, press and hold the pairing button until the LED turns fast, flashing white.
(2) To enter the subwoofer pairing mode on the soundbar, press and hold the bass button on the remote control for more than three seconds. Then, press VOL - on the remote control.
On the soundbar LED display:
→ "SUB PAIRING": The subwoofer is ready for pairing.
→ "SUB PAIRED": The subwoofer is connected.Was this helpful? Thank you for your feedback! -
USB Stick
- Get an empty
stick with speed of 2.0.
- Make sure it is formatted with FAT16 or FAT32.
- Your Music files can only be:
(32-320kbit/s),
(32-320kbit/s) and
(44.1K/48K/192K).
- The Partybox supports up to 8 subfolders.
- It will be played in alphabetic sequence with main folders first then subfolders.
- To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.
Was this helpful? Thank you for your feedback! - Get an empty
-
This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.
Was this helpful? Thank you for your feedback! -
Prerequisites:
− Make sure that your room is quiet;
− Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
− Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.
The calibration is done in two steps: Listening zone & Speaker positionCalibrate the listening zone
1. Place the detachable rear speakers beside your seating position.
2. On the remote control, press and hold HDMI until “1-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “1-DONE”: Calibration of the listening zone is completed successfully.Calibrate the speaker position
1. Place the detachable rear speakers in your desired location.
2. On the remote control, press and hold HDMI until “2-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “2-DONE”: Calibration of the speaker position is completed successfully.
3. To select suitable surround sound level, press repeatedly to switch between high, low or middle (default).
NOTES:
− During calibration, all buttons on the remote control are disabled except for STANDBY and HDMI.
− “SETUP FAILED” is displayed if calibration failed.Was this helpful? Thank you for your feedback! -
To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.Was this helpful? Thank you for your feedback! -
We included a Remote Control in your box (I know, that's sweet of us), and you need to pair it with your LINK BAR before it is working.
This is how you will do it- Press the BLUETOOTH button on the LINK BAR
- Now hold the BLUETOOTH button down for 3-5 seconds.
- When you see "SEARCHING FOR ACCESSORIES" on your TV screen, release the BLUETOOTH button.
- On your REMOTE press the HOME and BACK buttons at the same time.
- A Green LED light will flash on the REMOTE to indicate that it is in pairing mode.
- Keep holding down the buttons until you see a message on the TV screen that says, "Pairing remote control to LINK BAR" After 10 seconds, release.
- If done successfully on your TV screen, you will see an indicator counting down that it will "pair" with your remote.
BONUS TIP: There is an Android app called Android TV that will turn your Smartphone into a Remote controller.Was this helpful? Thank you for your feedback! -
Finding the software version
- Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
- A voice will start prompting numbers which indicates the current software version.
Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with Us
Mon - Fri - 10:00 a.m 7:00 p.m (NZST)