JBL EVEREST™ ELITE 750NC
|Driver size (mm)||40.0|
|Driver sensitivity at 1kHz/1mW (dB)||92dB@1kHz, 1mW|
|Dynamic frequency response range (Hz)||10Hz-22kHz|
|Number of drivers per ear||1.0|
|Headphone cable length (cm)||120.0|
|Headphone cable length (ft)||3.93|
Control Connect Specifications
|Bluetooth profiles||HFP v1.6, HSP v1.2, A2DP v1.2, AVRCP v1.4|
|Bluetooth transmitted modulation||GFSK, π/4-DQPSK, 8DPSK|
|Bluetooth transmitter power||4 dbm|
Documents & Downloads
Quick Start Guide
What’s in the Box
- 1 x Headphones
- 1 x Detachable remote cable
- 1 x Charging cable
- 1 x Carrying case
- 1 x Flight Adaptor
- 1 x Quick start guide
- 1 x Warning card
- 1 x Warranty card
- 1 x Safety sheet
FAQs & How-Tos
Are the materials of the Everest 750NC headphones non-leather?
Yes. Our Everest series headphones are made with synthetic protein leather which is a non-animal leather.
How do I power on and pair the Everest 750NC headphones?
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.
How do I reset my JBL Everest 310, 710 and 750 Elite headphones?
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.
Can you connect to multiple devices on the 750NC?
No. Unfortunately, you cannot connect to multiple devices on the 750NC Wireless headphones. You can pair to multiple devices, but can only be connected to one device at a time. The Everest 710 and 310 feature ShareMe 2.0, which permits listening to the same source over two headphones, wirelessly.
Can I use the Everest Noise Cancelling feature while plugged into a device with my audio cable or flight adapter?
No. The only way that the Noise Cancellation feature can be activated is while you are using the headphones wirelessly. You cannot use NC while the headphones are plugged into a device or charging.
Can the EVEREST ELITE be used with other apps?
No, the My JBL Harman app is made for use with ELITE models, and they can only be used with this app.
How do I skip tracks on the Everest 750NC?
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.
Do the Everest Series headphones support AAC or aptX?
Sorry, neither AAC nor aptX are supported.
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
My JBL Headphones App SupportThis headphone is supported by the My JBL Headphones App.
Does the audio cable on the Everest 750NC feature volume control?
No the audio cable included with the Everest series headphones has a one-button remote control with microphone. It does not have volume buttons. It can perform pause/play, and gives you the ability to answer and hang up phone calls. However, you can control the volume when the headphones are connected to a source device with Bluetooth, using the buttons on the ear cup.