Noise-Cancelling
-
Re-establishing Volume Levels/Balance between Earbuds and chargingAs with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.
If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.Was this helpful? Thank you for your feedback!Cleaning Instructions for Re-establishing ChargingIt is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.Was this helpful? Thank you for your feedback!Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!Pairing issues with a Smartphone or Tablet1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.Was this helpful? Thank you for your feedback! -
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!Pairing issues with a Smartphone or Tablet1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.Was this helpful? Thank you for your feedback!Can my headphones be connected to two devices simultaneously?Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices.Was this helpful? Thank you for your feedback!How to avoid Bluetooth Interference or Interruptions• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.Was this helpful? Thank you for your feedback! -
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!Pairing issues with a Smartphone or Tablet1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.Was this helpful? Thank you for your feedback!Can my headphones be connected to two devices simultaneously?Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices.Was this helpful? Thank you for your feedback!Voice Assistant Headphone ConnectionIf you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.
https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1Was this helpful? Thank you for your feedback! -
Silent Now InformationThe SilentNow feature allows you to activate Noise Cancelling without using Bluetooth, i.e. simply turning on ANC without playing music. A useful feature if you just want to enjoy a quiet moment or would like to rest on a long-haul flight.
Was this helpful? Thank you for your feedback!How to use Google Assistant with your headphonesAfter setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.
Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones
Get your notifications
Double-tap the Action button.
Stop your Google Assistant
Touch the Action button.
Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.
For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones
Was this helpful? Thank you for your feedback!My JBL Headphones App SupportThis headphone is supported by the My JBL Headphones App.Was this helpful? Thank you for your feedback!How to connect your headphones to the Google Assistant for Android devicesIf not pre-installed on your Android device, visit your App store to download the ‘Google Assistant’ App.
After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.Step 1
Follow the steps to connect and pair “JBL XXXX-LE” (depends on your model) with your devices.
Once set up is complete, you will see the below screen:Step 2
PLEASE NOTE: In order to verbally interact with your Google Assistant via the headphone you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under: Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.Was this helpful? Thank you for your feedback! -
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!How to use Google Assistant with your headphonesAfter setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.
Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones
Get your notifications
Double-tap the Action button.
Stop your Google Assistant
Touch the Action button.
Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.
For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones
Was this helpful? Thank you for your feedback!Pairing issues with a Smartphone or Tablet1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.Was this helpful? Thank you for your feedback!My JBL Headphones App SupportThis headphone is supported by the My JBL Headphones App.Was this helpful? Thank you for your feedback! -
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!Pairing issues with a Smartphone or Tablet1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.Was this helpful? Thank you for your feedback!Can my headphones be connected to two devices simultaneously?Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices.Was this helpful? Thank you for your feedback!Voice Assistant Headphone ConnectionIf you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.
https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1Was this helpful? Thank you for your feedback! -
How to Perform a Hardware ResetTo perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.Was this helpful? Thank you for your feedback!How to Factory Reset True Wireless Stereo EarbudsDouble-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off).
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.Was this helpful? Thank you for your feedback!Cleaning Instructions for Re-establishing ChargingIt is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.Was this helpful? Thank you for your feedback!Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback! -
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!How to use Google Assistant with your headphonesAfter setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.
Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones
Get your notifications
Double-tap the Action button.
Stop your Google Assistant
Touch the Action button.
Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.
For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones
Was this helpful? Thank you for your feedback!Pairing issues with a Smartphone or Tablet1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.Was this helpful? Thank you for your feedback!My JBL Headphones App SupportThis headphone is supported by the My JBL Headphones App.Was this helpful? Thank you for your feedback! -
How to Perform a Hardware ResetTo perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.Was this helpful? Thank you for your feedback!How to Factory Reset True Wireless Stereo EarbudsDouble-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off).
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.Was this helpful? Thank you for your feedback!Cleaning Instructions for Re-establishing ChargingIt is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.Was this helpful? Thank you for your feedback!Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback! -
How to Perform a Hardware ResetTo perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.Was this helpful? Thank you for your feedback!How to Factory Reset True Wireless Stereo EarbudsDouble-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off).
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.Was this helpful? Thank you for your feedback!My JBL Headphones App - Available DJ SignaturesSome of the DJ EQ curves have been removed from the My JBL Headphones app. Harman will ‘continuously’ update the My JBL Headphones app with new DJ sound-curves as this number changes based on who we sign agreements with and when.
See the release notes for app version 4.10.9 below:
- Adding support for TOUR PRO+ TWS and TOUR ONE Global version
- Removing expired DJ’s signaturesWas this helpful? Thank you for your feedback!Cleaning Instructions for Re-establishing ChargingIt is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.Was this helpful? Thank you for your feedback! -
Silent Now InformationThe SilentNow feature allows you to activate Noise Cancelling without using Bluetooth, i.e. simply turning on ANC without playing music. A useful feature if you just want to enjoy a quiet moment or would like to rest on a long-haul flight.
Was this helpful? Thank you for your feedback!My JBL Headphones App - Available DJ SignaturesSome of the DJ EQ curves have been removed from the My JBL Headphones app. Harman will ‘continuously’ update the My JBL Headphones app with new DJ sound-curves as this number changes based on who we sign agreements with and when.
See the release notes for app version 4.10.9 below:
- Adding support for TOUR PRO+ TWS and TOUR ONE Global version
- Removing expired DJ’s signaturesWas this helpful? Thank you for your feedback!Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!How to use Google Assistant with your headphonesAfter setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.
Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones
Get your notifications
Double-tap the Action button.
Stop your Google Assistant
Touch the Action button.
Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.
For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones
Was this helpful? Thank you for your feedback! -
Silent Now InformationThe SilentNow feature allows you to activate Noise Cancelling without using Bluetooth, i.e. simply turning on ANC without playing music. A useful feature if you just want to enjoy a quiet moment or would like to rest on a long-haul flight.
Was this helpful? Thank you for your feedback!My JBL Headphones App - Available DJ SignaturesSome of the DJ EQ curves have been removed from the My JBL Headphones app. Harman will ‘continuously’ update the My JBL Headphones app with new DJ sound-curves as this number changes based on who we sign agreements with and when.
See the release notes for app version 4.10.9 below:
- Adding support for TOUR PRO+ TWS and TOUR ONE Global version
- Removing expired DJ’s signaturesWas this helpful? Thank you for your feedback!Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!How to use Google Assistant with your headphonesAfter setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.
Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones
Get your notifications
Double-tap the Action button.
Stop your Google Assistant
Touch the Action button.
Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.
For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones
Was this helpful? Thank you for your feedback! -
Can I listen to music while charging?Yes, you can listen to music via cabled connection while you charge the battery. As soon as you insert the charging cable, all active circuits are switched off, and only the analog cable input remains active. When charging has finished, you can use the wireless and noise cancelling functions again.Was this helpful? Thank you for your feedback!Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
Was this helpful? Thank you for your feedback!Can I place or answer telephone calls with my JBL LIVE headphones?Yes, you can use them for telephone conversations in both Bluetooth and wired mode when paired with a smart device.Was this helpful? Thank you for your feedback!I cannot activate my voice assistant when touching the dedicated button.Please check that Google Assistant or Amazon Alexa are installed on your device.
Try to repeat the setup process.
Also, switching the headphones off and on once or twice may solve the problem.Was this helpful? Thank you for your feedback! -
Further Support
Gaming Support
Need help with your JBL Quantum? Check out the Quantum support page!
Go to Quantum Support!Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00