JBL Tune 110

Product Specifications

Generelle Spesifikasjoner

Driver size (mm): 9.0

Number of Microphones: 1

Spesifikasjoner lyd

Driver sensitivity at 1kHz/1mW (dB): 96.0

Dynamic frequency response range (Hz): 20 Hz - 20 kHz

Impedance (ohms): 16.0

Number of drivers per ear: 1.0

Dimensjoner

Headphone cable length (cm): 111.3

Headphone cable length (ft): 3.65

Headphone cable length (m): 111.3

Weight (g): 12.7

Weight (oz): 0.45

Utstyr

Built-in Microphone: Ja

Flat Cable: Ja

Hands Free Call: Ja

JBL Pure Bass Sound: Ja

Speed charge: Nei

Bass for rock’n roll.

Introduksjon av JBL TUNE110 hodetelefoner. De er lette, veier lite, er komfortable og kompakte. Under overflaten trykker et par 9mm drivere til med en seriøs bass, som gjengir den kraftige JBL Pure Bass-lyden som du opplever i konserthaller, arenaer og opptaksstudioer over hele verden. I tillegg lar en enkel fjernkontrollknapp deg kontrollere musikkavspilling og innkommende anrop i farten, med en innebygget mikrofon. Dette gjør JBL TUNE110 til din hverdagskompis på jobb, hjemme og på tur.

JBL Pure Bass-lyd

I over 60 år har JBL konstruert nøyaktig, imponerende lyd som vi kan finne på store arenaer over hele verden. Disse hodetelefonene gjengir den samme JUL-lyden og trykker til med en bass som er både dyp og kraftig.

1-knapps fjernkontroll med mikrofon

Kontroller musikkavspilling med en-knapps fjernkontroll Får du en telefonsamtale? Besvar den i farten med innebygget mikrofon.

Flat kabel som ikke vikler seg

En holdbar flat kabel som ikke vikler seg opp i knuter.

FAQs & How-Tos

5 results

Sort

Page size

aptX Audio Codec Support

This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.

Was this helpful? Thank you for your feedback!
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.

Was this helpful? Thank you for your feedback!
How do I charge the T110BT headphones?

The USB charging port will be located on the inline microphone located on the RIGHT side of the earphones.

Was this helpful? Thank you for your feedback!
T110BT Headphones: Power and Pairing Information

To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.

Was this helpful? Thank you for your feedback!
Waterproof Information

This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.

Was this helpful? Thank you for your feedback!