In Ear Headphones

In Ear Headphones

  • Re-establishing Volume Levels/Balance between Earbuds
    As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds and your ears. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing.

    If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

    cleaning-earstick-tip 
    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
    Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    More FAQs

Further Support

Watch & Learn

Have you seen our Youtube channel?

Many of our products have videos introducing them.

Learn more

Can’t find what you’re looking for?

Call Us

Call Us

Talk to a product expert
Call us now at: +60 377240321

Mon - Fri - 8:00 a.m 5:00 p.m (MYT)

E-mail Us

E-mail Us

365 days a year

We will respond within one business day.

Email Us
Chat with Us

Chat with Us

Mon - Fri - 8:00 a.m 5:00 p.m (MYT)

message

Text Us

Chat with a support agent via SMS at:
601130116117

Mon - Fri: 8:00 am - 5:00 pm (MYT)