JBL BAR 9.1 True Wireless Surround with Dolby Atmos
Dolby Atmos® 및 서라운드 스피커가 적용된 9.1 채널 사운드바 시스템
2020 부터 현재까지 판매
JBL BAR 9.1 True Wireless Surround with Dolby Atmos 제품 사용 시작하기
문서 및 다운로드
제품 사양
- 사운드 시스템
- 5.1.4 채널
- 전원 공급 장치
- 100~240V AC, ~50/60Hz
- 배터리 충전 시간 3 시간
- 총 스피커 전원 출력(최대 @THD 1%)
- 820W
- 사운드바 출력 전원(최대 @THD 1%)
- 400W
- 서라운드 스피커 출력 전원(최대 @THD 1%)
- 2 x 60W
- 서브우퍼 출력 전원(최대 @THD 1%)
- 300W
- 사운드바 변환기
- 레이스트랙 드라이버 4 개 + 업파이어링 풀레인지 드라이버 2개 + 3 x 0.75인치 트위터
- 서라운드 변환기(개당)
- 업파이어링 풀레인지 드라이버개 + 0.75인치 트위터
- 서브우퍼 변환기
- 10”
- 작동 온도
- 0°C~45°C
- 305 x 440 x 305mm/12.0 x 17.3 x 12.0인치 (서브우퍼)
- 3.64kg/ 8.0 lb(사운드바)
- 0.72kg x 2/ 1.6 lb x2 (탈착식 서라운드 스피커)
- 11.10kg/ 24.5 lb (서브우퍼
- 사운드바 대기(모든 무선 연결이 비활성화된 경우) < 0.5 W
- 네트워크 대기(사운드바) < 6.0 W
- 네트워크 대기(서브우퍼) < 2.0 W
- 대기 전환 시간
- <10분
- HDMI 비디오 입력
- 1
- HDMI 비디오 출력(향상된 Audio Return Channel, eARC)
- 1
- HDMI HDCP 버전
- 2.3
- 최대 SPL
- 103dB
- 주파수 응답
- 34Hz~20KHz
- 오디오 입력
- 1 - Optical, Bluetooth, Chromecast, AirPlay2, USB
- 변조 형식
- QPSK, BPSK, 16QAM, 64QAM, 256QAM
- 5G 무선 주파수 범위
- 5180.0 MHz~5240.0 MHz, 5725.0 MHz~5825.0 MHz
- 5G 최대 송신 전력
- 13 dBm(EIRP)
- 변조 형식
- QPSK
- 884 x 62 x 120mm/34.8 x 2.4 x 4.7인치 (사운드바)
- 173 x 60 x 120mm/6.8 x 2.4 x 4.7인치 (탈착식 서라운드 스피커, 개당)
- USB 포트
- A형
- USB 정격
- 5V/ 500mA
- 지원 파일 형식
- MP3
- MP3 코덱
- MPEG 1 Layer 2/3, MPEG 2 Layer 3, MPEG 2.5 Layer 3
- MP3 샘플링 속도
- 16KHz~48KHz
- MP3 비트율
- 80kbps~320kbps
- (USB 재생은 미국 버전만 가능. 기타 버전에서 USB는 서비스 전용입니다.)
- Bluetooth 버전
- 4.2
- Bluetooth 프로필
- A2DP V1.2, AVRCP V1.5
- Bluetooth 주파수 범위
- 2402MHz~2480MHz
- Bluetooth 최대 송신 전력
- 13 dBm(EIRP)
- 변조 형식
- GFSK, π/4 DQPSK, 8DPSK
- Wi-Fi 네트워크
- IEEE 802.11 a/b/g/n/ac(2.4GHz/5GHz)
- 2.4G Wi-Fi 주파수 범위
- 2412~2472 MHz(2.4GHz ISM 밴드, 미국 11개 채널, 유럽 및 기타 지역 13개 채널)
- 2.4G Wi-Fi 최대 송신 전력
- 20dBm(EIRP)
- 변조 형식
- DBPSK, DQPSK, CCK, QPSK, BPSK, 16QAM, 64QAM
- 5G Wi-Fi 주파수 범위
- 5.15GHz~5.35GHz, 5.470GHz~5.725GHz, 5.725GHz~5.825GHz
- 5G Wi-Fi 최대 송신 전력
- 22dBm(EIRP)
마치 3D 서라운드 사운드와 함께 하는 기분을 느껴보세요
JBL Bar 9.1 사운드 바는 2개의 탈착식 서라운드 스피커와 Dolby Atmos® 및 DTS:X™ 3D 사운드의 타격감을 적용해 영화관의 오디오를 집에서도 경험할 수 있습니다. 820W의 시스템 전체 출력 덕분에 파워풀하고 선명한 오디오 음색으로 오스카에 버금가는 모든 공연을 즐길 수 있습니다. 10" 서브우퍼의 볼륨을 높여 강력한 저음을 경험하거나 볼륨을 낮추고 Chromecast 및 AirPlay 음악 스트리밍으로 안락한 휴식을 취하세요. 최신 블록버스터 영화에 몰입하거나 선호하는 영화 또는 스포츠 장면을 다시 경험하세요. 놀라운 홈 시네마 사운드 경험이 여기에 있습니다.
FAQ 및 사용 방법
-
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
Prerequisites:
− Make sure that your room is quiet;
− Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
− Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.
The calibration is done in two steps: Listening zone & Speaker positionCalibrate the listening zone
1. Place the detachable rear speakers beside your seating position.
2. On the remote control, press and hold HDMI until “1-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “1-DONE”: Calibration of the listening zone is completed successfully.Calibrate the speaker position
1. Place the detachable rear speakers in your desired location.
2. On the remote control, press and hold HDMI until “2-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “2-DONE”: Calibration of the speaker position is completed successfully.
3. To select suitable surround sound level, press repeatedly to switch between high, low or middle (default).
NOTES:
− During calibration, all buttons on the remote control are disabled except for STANDBY and HDMI.
− “SETUP FAILED” is displayed if calibration failed.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
With our JBL BAR 9.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings. Let us walk through each one of them. Resetting WiFi settings Turn on your JBL BAR 9.1 Surround. Press and hold POWER button down for more than 10 seconds. All of your WiFi configuration is lost and you need to reinstall it again. Use the Google Home app to install the device on your WiFi network. Resetting to Factory default settings Turn on your JBL BAR 9.1 Surround Press and hold POWER and SOURCE button for 3 seconds. Your device is now reset. You can now start allover with installing your BAR 9.1 Surround.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!