How To
How To
-
To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
If you are experiencing issues with your headphones' Bluetooth disconnecting and reconnecting while on standby, there is a new Firmware Update app to resolve this issue. Start by downloading the app "JBL Firmware Update" (see links below).
Google Play Store: https://play.google.com/store/apps/details?id=com.jbl.tune.update
App Store: https://apps.apple.com/gb/app/jbl-firmware-update/id1548227663
Once downloaded, you can update your headphones firmware from there.
Below you can see step by step images of the update process.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
Horizon's alarm sounds for 3 minutes, then it shuts off, or rather it goes into snooze, for 9 minutes. Then it sounds the alarm again for 3 minutes, followed by snooze for another 9 minutes. After this final snooze period, it starts playing, and keeps on playing until it is manually shut off. The light shuts off with the audio.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
These headphones consist of plastics, synthetic leathers and foams. All JBL Jr products were put through extensive tests and are compliant with Standard Consumer Safety Specification for Toy Safety.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
Once the sound bar is connected to the network, software updates will automatically be sent to the speaker/soundbar through Wi-Fi or the internet, if available해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
In the JBL ONE App:
(1) Go to My Products, select your product
(2) Select Support tile
(3) Under General, select Product Support해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
To play the surround sound with DOLBY ATMOS or DTS:X, connect your Blu-ray player or other digital device to the HDMI input connector on the soundbar. If the TV support Dolby ATMOS, served over HDMI ARC, just make sure it is selected in the TV setting menu. To select the most suitable amount of sound effect of DOLBY ATMOS and DTS:X, press on the remote control ATMOS level button, to switch between MID, HIGH, LOW or OFF. Note: If your TV has an eARC HDMI input, you can connect your Blu-ray player or other digital device to the HDMI IN connector on the TV.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
You can reset the E25BT in two ways: 1: Press and hold Volume + and Volume - simultaneously for more than 3 seconds. This resets to factory settings, clearing the pairing list. 2: With unit in ON mode, plug in the USB cable. This resets the unit and puts it into charging mode.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
The owner's manual can be a bit difficult to understand. Here is what to do to program a preset station that has not already been saved in any preset: 1 Turn on the radio by clicking the FM button. 2 Find the station you want to save by doing what is shown under pt. 8 B or C, either clicking or pressing/holding for more than 2 seconds the left/right arrow buttons. 3 Press and hold the FM button for more than 2 seconds. Now the preset number appears blinking. 4 Click on the left/right arrow buttons to skip through the preset positions. 5 When you have located the desired memory preset position, such as Preset 4, confirm by clicking the FM button. Now the desired FM station is saved in memory preset 4. If you have already saved an FM station in a preset memory position, and want to have a new station placed there instead, here is what to do: 1 Turn on the radio by clicking the FM button. 2 Jump to the preset station you want to change with the round central button. Each click advances to the next preset. 3 When you are on the preset you want to change, e.g. preset 4, press and hold the FM button for more than 2 seconds. 4 The FM symbol and the frequency will now blink. 5 Before they stop blinking, click, or press and hold one of the arrow buttons to go through the FM frequencies step by step, or perform station search. 6 When you have found the new station you want to save in preset 4, click the round central button. 7 Now the new station is saved in preset 4.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
(1) Select the JBL soundbar you want to rename
(2) Navigate to the Support tile and select "Rename My Product."
(3) Press the current name and type in the new name
(4) Press SAVE해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
Prerequisites:
− Make sure that your room is quiet;
− Make sure that the soundbar and the two detachable rear speakers are fully in sight of each other, without obstacles in between.
− Make sure that the left and right rear speakers are properly placed, the L speaker on the left and the R speaker on the right.
The calibration is done in two steps: Listening zone & Speaker positionCalibrate the listening zone
1. Place the detachable rear speakers beside your seating position.
2. On the remote control, press and hold HDMI until “1-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “1-DONE”: Calibration of the listening zone is completed successfully.Calibrate the speaker position
1. Place the detachable rear speakers in your desired location.
2. On the remote control, press and hold HDMI until “2-CALIBRATION” is displayed on the soundbar.
→ Countdown starts from 5 to 1.
→ Calibration tone is heard. Audio calibration starts.
→ “CALIBRATING”: Calibration ongoing.
→ “2-DONE”: Calibration of the speaker position is completed successfully.
3. To select suitable surround sound level, press repeatedly to switch between high, low or middle (default).
NOTES:
− During calibration, all buttons on the remote control are disabled except for STANDBY and HDMI.
− “SETUP FAILED” is displayed if calibration failed.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
(1) On the subwoofer's rear panel, press and hold the pairing button until the LED turns fast, flashing white.
(2) To enter the subwoofer pairing mode on the soundbar, press and hold the bass button on the remote control for more than three seconds. Then, press VOL - on the remote control.
On the soundbar LED display:
→ "SUB PAIRING": The subwoofer is ready for pairing.
→ "SUB PAIRED": The subwoofer is connected.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
Resetting the Partybox to Factory Settings
- Press and hold "Play/Pause" and "Volume +" down for > 10 seconds.
- The JBL Partybox will power off and back on and is now reset.
해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
The factory reset button restores your device to the default settings, including network and audio configurations.
Please use one of the following solutions:- Press and hold VOL -, VOL +, and Source buttons on the device at the same time until the LED light flashes (hold for more than 5 seconds)
- Open your JBL ONE App.
- Navigate to the support tile.
- Select RESTORE FACTORY SETTINGS.
해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
With our JBL BAR 9.1 Surround there is two types of resets, one is to reset the WiFi settings and last one is to restore factory default settings. Let us walk through each one of them. Resetting WiFi settings Turn on your JBL BAR 9.1 Surround. Press and hold POWER button down for more than 10 seconds. All of your WiFi configuration is lost and you need to reinstall it again. Use the Google Home app to install the device on your WiFi network. Resetting to Factory default settings Turn on your JBL BAR 9.1 Surround Press and hold POWER and SOURCE button for 3 seconds. Your device is now reset. You can now start allover with installing your BAR 9.1 Surround.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
(1) Use JBL One App to set up the My Moment Feature.
(2) Select the JBL soundbar you want to set your favorite music to the My Moment feature.
(3) Tap the My Moment card to assign music.
(4) Click Add Music to manage music streaming services and specific music tracks.
(5) Set the timer to inactive speaker/soundbar (optional)
(6) Set the music loudness (optional)
(7) Press SAVE해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone. 해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
The new Boombox 2 does not feature the Indoor/Outdoor Mode. With the first generation Boombox, the Outdoor Mode was loud, but lacking sufficient bass. The Boombox 2 has both improved bass and loudness to create the perfect balanced sound for all environments.
해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
Is Bluetooth APT X streaming supported by the JBL Bar Studio, Bar 2.1, Bar 3.1, Bar 5.1 and Bar 9.1?The speaker uses Bluetooth version 4.2 but does NOT support APT X.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
Yes. All but the Bar Studio model have an LED display on the soundbar's front panel. The display tells which source input, volume level, and sound feature you are on. You are able to dim the display, using the remote, during low light usage.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
This model is supported by the JBL Partybox App.
Download the JBL Partybox App from the App Store or Google Play Store and install it to use the following features:
SETTINGS: OTA update | Firmware Version | Quick Start Guide
REMOTE CONTROL: Music playback – Play/Pause & Skip Track | Karaoke – Bass/Treble/Echo | DJ sound effect – Here you can swap which samples will play when you hit the three Sound Effect buttons on the top panel, or play all of the available sounds on one screen | Top panel control | Source select | Bass Boost – On/Off
LIGHT SHOW: Fully customize your light show in real time – Change light themes and animations to suit your mood | Turn animations on or off | Turn the strobe on or off | Customize color (preset or color palette) | SOLO mode
GET LOUD: Connect in TWS, switch Stereo channels and enable Party Mode해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다! -
This headphone does not feature volume control. You must manually control volume from your device.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
When you place the two Free earphones in the charging case, you will see a white led ring light up on both of them. At the same time, some of the four dot-leds on the charging case will light up to indicate the battery level of the case battery. When the earphones are fully charged, the white led ring goes out on each of them. When both are fully charged, the charging case charging level leds go out too.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
The JBL Free automatically switches from stereo to mono when making or taking phone calls. Voice calls will only come through the right ear piece for a more natural call experience.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!
-
JBL Quantum 100에는 JBL QuantumSURROUND가 장착되어 있지 않습니다. USB 동글이 제공되고 JBL QuantumENGINE에 액세스 할 수 있는, JBL Quantum 300을 구매하실 수 있습니다.해당 내용이 도움이 되었나요? 피드백을 주셔서 감사합니다!