JBL Tune 125TWS - Pink - True wireless earbuds - Hero JBL Tune 125TWS - Pink - True wireless earbuds - Front JBL Tune 125TWS - Pink - True wireless earbuds - Detailshot 1
JBL Tune 125TWS - Pink - True wireless earbuds - Hero
  • JBL Tune 125TWS - Pink - True wireless earbuds - Swatch Image
  • JBL Tune 125TWS - Green - True wireless earbuds - Swatch Image
  • JBL Tune 125TWS - Blue - True wireless earbuds - Swatch Image
  • JBL Tune 125TWS - White - True wireless earbuds - Swatch Image
  • JBL Tune 125TWS - Black - True wireless earbuds - Swatch Image
  • JBL Tune 125TWS - Gold - True wireless earbuds - Swatch Image

JBL Tune 125TWS

나만의 세상에 푹 빠져보세요. 음악을 듣거나 전화를 받을 때 코드에 걸리는 일이 없습니다. 간편하게 JBL TUNE 125TWS 이어버드를 귀에 꽂고 사운드를 느껴보세요. 케이스에서 꺼내면 바로 기기에 연결됩니다. 듀얼 커넥트 기능으로 필요에 따라 이어버드를 한쪽만 쓰거나 양쪽 모두 사용할 수 있습니다. JBL 퓨어 베이스 덕분에 좋아하는 아티스트의 음악이 더욱 놀라워집니다. 최대 32시간의 배터리 사용시간과 편안한 착용감으로 음악을 하루 종일 감상할 수 있습니다. 놀랄 만큼 다양한 색상으로 출시되어 스타일에 맞는 진정한 무선 헤드폰을 선택할 수 있습니다.

제품 사양

General Specifications

Driver size (mm) 5.8

Audio Specifications

Driver sensitivity at 1kHz/1mW (dB) 96
Dynamic frequency response range (Hz) 20 Hz – 20 kHz
Impedance (ohms) 14
Number of drivers per ear 1

Dimension Specifications

충전케이스 무게 (온스) 2.1
이어폰 무게(온스) 0.5
충전케이스 무게 (그램) 60.1
이어폰 무게(그램) 13.6

Control Connect Specifications

Bluetooth profiles A2DP 1.3, AVRCP 1.5, HFP V1.7
Bluetooth frequency 2.402 GHz – 2.480 GHz
Bluetooth transmitted modulation GFSK, π/4DQPSK, 8DPSK
Bluetooth transmitter power 0 - 12dbm
Bluetooth version 5.0
자세한 사양은 문서를 참조하십시오.

문서 및 다운로드

비디오

박스 구성품

  • JBL TUNE 125TWS
  • 3가지 크기(S, M, L)의 이어팁
  • C형 USB 충전 케이블
  • 충전 케이스
  • 품질보증서/경고 1부(W/!)
  • QSG/안전 관리 지침 1부(S/i)
JBL Tune 125TWS - What's in the Box

FAQ 및 사용 방법

Re-establishing Volume Levels/Balance between Earbuds
As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds and your ears. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

cleaning-earstick-tip 
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

Waterproof Information
This product does not feature an IPX rating and is not waterproof. Over exposure to water or moisture can result in irreversible damage to this unit.
이어버드 세척 방법
CLEANING THE PRODUCT V2.JPG
CLEANING THE PRODUCT TWS.JPG  
깨끗한 면봉을 사용하여 알코올로 살짝 적셔서 다음을 수행합니다.
  1. 이어버드의 이어팁에서 귀지와 오염을 제거합니다.
  2. 이어버드와 충전 케이스에서 각각 충전 패드와 포트를 세척합니다. 그런 다음 부드럽고 물에 젖지 않은 상태의 마른 면직물을 사용하여 먼지와 보풀을 문질러 닦아냅니다.
  3. 충전 케이스의 뚜껑과 바닥의 홈을 세척합니다.
세척을 마치면, 반드시 충전 케이스와 이어버드가 마른 후에 이어버드를 충전 케이스에 다시 넣습니다.

팁:
이러한 작업을 대략 몇 주마다 반복하여 헤드폰을 깨끗하게 유지함으로써 충전 속도와 품질에 영향을 주지 않도록 할 것을 권장합니다.
True Wireless 헤드폰 세척 지침
True Wireless 헤드폰의 충전 문제는 흔히 발생합니다.
때때로 충전이 중단될 수 있습니다. 충전이 아예 시작되지 않거나 이어 버드 한쪽의 전원이 갑자기 켜지고 페어링 절차가 시작되는 경우가 발생할 수 있습니다.

이는 거의 대부분 충전 접촉부의 오염이 원인입니다. 
이러한 접촉부는 취약한데 땀, 피부 유분이나 귀지로 쉽게 오염될 수 있기 때문입니다.
대개 금도금이 되어 있으나, 금도금은 표면 오염을 막지는 못합니다.

충전 문제가 발생하면, 우선 각 이어 버드 양쪽과 충전 케이스의 모든 접촉부를 늘 깨끗하게 해야 합니다.
미세한 구멍까지 닿기는 쉽지 않을 수 있으나, 일반 면봉이나 메이크업용 면봉을 사용하면 됩니다.   끝을 소독용 알코올로 살짝 적신 다음, 각 접촉면에 가볍게 문질러서 닦아냅니다.
접촉부가 깨끗해 보일 때까지 반복하면, 충전이 제대로 작동됩니다.
컴퓨터나 PC와의 페어링 문제
대부분의 경우 컴퓨터/PC/노트북이 블루투스 기기(휴대용 스피커, 헤드폰, 액티브 스피커)에 연결되면서 문제가 발생하며, 이는 컴퓨터/PC/노트북의 블루투스 드라이버(소프트웨어)가 원인입니다.

드라이버(소프트웨어)가 다음과 같은 블루투스 프로토콜을 지원해야, 컴퓨터/PC/노트북에서 음악/소리를 재생할 수 있습니다.

• A2DP(고급 오디오 배포 프로필) 드라이버(사용자의 컴퓨터/PC/노트북에 음악 전송용).

• AVRCP(오디오/동영상 원격 제어 프로필) 드라이버(사용자의 기기에 대한 음악 건너뛰기/앞으로/일시정지/재생 명령 전송용)

반드시 사용자의 컴퓨터/PC/노트북용으로 제공되는 최신 드라이버 버전을 설치합니다.

올바른 드라이버(소프트웨어)를 다운로드하려면, 사용자의 컴퓨터/PC/노트북 제조업체의 웹사이트를 확인합니다. 일반적으로 ‘지원/다운로드’ 섹션에서 맞는 드라이버를 찾을 수 있습니다. 혹은, 해당 업체의 서비스 지원 센터에 연락하기를 권장합니다.

Microsoft/Windows 시스템에서 제공되는 표준 드라이버는 적합하지 않으며 오류 메시지가 표시되거나(PIN 코드를 입력해야 하는 등), 페어링이 작동하지 않습니다.
How to clean your earbuds
                                                                                             CLEANING THE PRODUCT V2.JPG
CLEANING THE PRODUCT TWS.JPG  
Use a clean cotton swab slightly moistened with alcohol to:
  1. Remove earwax and dirt from the ear tips on your earbuds.
  2. Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
  3. Clean the grooves on the cover and at the bottom of the charging case.
After cleaning, make sure the charging case and earbuds are dry before putting the earbuds back into the charging case.

TIP: 
We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.
Is Volume Control Supported?
This headphone does not feature volume control. You must manually control volume from your device.
볼륨 컨트롤이 지원됩니까?
이 헤드폰은 볼륨 컨트롤 기능이 없습니다. 장치에서 볼륨을 수동으로 컨트롤해야 합니다.
헤드폰 및 제삼자 통신 앱(Skype, Zoom, WhatsApp 등)

헤드폰과 통신하는 앱을 입수하는 데 문제를 겪고 있다면, (이미 헤드폰을 기기와 페어링한 상태로 가정) 통신 앱 오디오 설정으로 이동합니다. 거기서 해결책을 찾을 수 있는 가능성이 높습니다. 사용하고 있는 앱에서 헤드폰을 ‘통신 기기’로 설정해야 할 수 있습니다. 

헤드폰과 통신하는 앱을 입수하는 데 문제를 겪고 있다면, (이미 헤드폰을 기기와 페어링한 상태로 가정) 통신 앱 오디오 설정으로 이동합니다. 거기서 해결책을 찾을 수 있는 가능성이 높습니다. 사용하고 있는 앱에서 헤드폰을 ‘통신 기기’로 설정해야 할 수 있습니다. 

aptX Audio Codec Support
This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.
How to avoid Bluetooth Interference or Interruptions
• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.

• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.

• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.

• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.

• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.

• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.
How to Turn off your TWS Headphones
1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).
Cleaning Instructions for Re-establishing Charging
It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
needed-tools.png
Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
cleaning-earbud-contact-points.png
Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
cleaning-charging-case.png
Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.
Pairing issues with a Computer or PC
In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
Pairing issues with a Smartphone or Tablet
1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
How to Factory Reset True Wireless Stereo Headphones
Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
True Wireless Stereo 헤드폰을 어떻게 리셋할 수 있나요?
양쪽 이어팟을 충전함에 넣고, 충전함을 전원에 연결합니다. 우측 팟의 버튼을 약 5초간 길게 누릅니다. 팟의 LED가 꺼진 다음 다시 켜집니다. 이로써 공장 초기 설정으로 복구됩니다. (리셋 작업을 수행하는 동안 충전이 진행되어야 합니다.)

Register your product

Do you own this product?
Register it here!
And claim your warranty or service easily

Register now

찾는 제품이 없나요?

연락하기

연락하기

제품 전문가에게 지금 전화하십시오. 02-553-3494

월~금, 오전 9시 오후6시