


JBL Live Free NC+ TWS
제품 사양
General Specifications
Bluetooth version | 5.1 |
---|---|
Ear tip material | Silicon |
Driver size (mm) | 6.8 |
Audio Specifications
Driver sensitivity at 1kHz/1mW (dB) | 96 |
---|---|
Dynamic frequency response range (Hz) | 20 Hz – 20 kHz |
Impedance (ohms) | 16 |
Number of drivers per ear | 1 |
Dimension Specifications
충전케이스 무게 (온스) | 1.4 |
---|---|
이어폰 무게(온스) | 0.5 |
충전케이스 무게 (그램) | 40 |
이어폰 무게(그램) | 14 |
Control Connect Specifications
Bluetooth profiles | A2DP V1.3, AVRCP V1.6, HFP V1.7 |
---|---|
Bluetooth frequency | 2.4 GHz – 2.4835 GHz |
Bluetooth transmitted modulation | GFSK, π/4DQPSK, 8DPSK |
Bluetooth transmitter power | 0 - 10dbm |
문서 및 다운로드
빠른 시작 안내
갤러리











비디오
박스 구성품
- JBL Live Free NC+ TWS
- 3가지 크기의 이어팁 각 1쌍
- 2가지 크기의 겔 슬리브 각 1쌍
- C형 USB 충전 케이블 1개
- 충전 케이스 1개
- 품질보증서/경고 1부(W/!)
- QSG/안전 관리 지침 1부(S/i)

FAQ 및 사용 방법
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.
This unit is IPX7 rated, which means that you can submerge the unit in water as deep as 3 feet (1 meter) for up to 30 minutes.

https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1
The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:
• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.
• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device
Always get the latest driver version available for your Computer/PC/Laptop.
To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.
The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

- Click the Plus(+) button on the top right of the screen.
- Then select ‘Add Device‘.
- Select headphones from the list and then choose your Headphones from the list of available devices.
- Follow the rest of the instructions in the Alexa App to complete the setup.
If the earbuds go into standby mode and turn off, you can still use them without putting them back into the charging case.
You can reactivate the headphones by pressing or touching the outside earbud itself.
Please note: They will be automatically powered off after 30 minutes of being in standby mode if they disconnect from Bluetooth. To reconnect, you will need to put the earbuds back in the charging case and take them off again.
It is possible to change the standby mode time with your headphones. To do this, go into the My JBL Headphones app and choose the Standby Time via Auto-off function. You can adjust the time to 15min, 1hr, etc., or you can choose “Never” if you want to keep the earbuds turn on at all times. Once you set the Auto-off, the earbuds will work according to the setting whether they connect to Bluetooth or disconnect.
때때로 충전이 중단될 수 있습니다. 충전이 아예 시작되지 않거나 이어 버드 한쪽의 전원이 갑자기 켜지고 페어링 절차가 시작되는 경우가 발생할 수 있습니다.
이는 거의 대부분 충전 접촉부의 오염이 원인입니다.
이러한 접촉부는 취약한데 땀, 피부 유분이나 귀지로 쉽게 오염될 수 있기 때문입니다.
대개 금도금이 되어 있으나, 금도금은 표면 오염을 막지는 못합니다.
충전 문제가 발생하면, 우선 각 이어 버드 양쪽과 충전 케이스의 모든 접촉부를 늘 깨끗하게 해야 합니다.
미세한 구멍까지 닿기는 쉽지 않을 수 있으나, 일반 면봉이나 메이크업용 면봉을 사용하면 됩니다. 끝을 소독용 알코올로 살짝 적신 다음, 각 접촉면에 가볍게 문질러서 닦아냅니다.
접촉부가 깨끗해 보일 때까지 반복하면, 충전이 제대로 작동됩니다.
After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.
Step 1

Follow the steps to connect and pair “JBL XXXX-LE” (depends on your model) with your devices.
Once set up is complete, you will see the below screen:
Step 2

PLEASE NOTE: In order to verbally interact with your Google Assistant via the headphone you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under: Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.


2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.

Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones
Get your notifications
Double-tap the Action button.
Stop your Google Assistant
Touch the Action button.
Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.
For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones
- Forget/unpair the headphones on your device.
- Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
- Pair the headphones to your device and see if this resolves the problem.
- If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
- Initiate a Product Reset to reset the earbud’s Bluetooth connection.
- Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
- Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
- Manually pair the 2 buds together again, as you did in step 2. This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
- Pair the buds to your Source Device.

Things to try
- “What’s the weather?”
- Play Niall Horan
- Play NPR on iHeartRadio
- Set a timer for 5 minutes
- What new skills do you have?
While Alexa is talking, press and release the Action button then say “Stop”.
For more information and things to try with Alexa, visit: www.amazon.com/alexadevices
드라이버(소프트웨어)가 다음과 같은 블루투스 프로토콜을 지원해야, 컴퓨터/PC/노트북에서 음악/소리를 재생할 수 있습니다.
• A2DP(고급 오디오 배포 프로필) 드라이버(사용자의 컴퓨터/PC/노트북에 음악 전송용).
• AVRCP(오디오/동영상 원격 제어 프로필) 드라이버(사용자의 기기에 대한 음악 건너뛰기/앞으로/일시정지/재생 명령 전송용)
반드시 사용자의 컴퓨터/PC/노트북용으로 제공되는 최신 드라이버 버전을 설치합니다.
올바른 드라이버(소프트웨어)를 다운로드하려면, 사용자의 컴퓨터/PC/노트북 제조업체의 웹사이트를 확인합니다. 일반적으로 ‘지원/다운로드’ 섹션에서 맞는 드라이버를 찾을 수 있습니다. 혹은, 해당 업체의 서비스 지원 센터에 연락하기를 권장합니다.
Microsoft/Windows 시스템에서 제공되는 표준 드라이버는 적합하지 않으며 오류 메시지가 표시되거나(PIN 코드를 입력해야 하는 등), 페어링이 작동하지 않습니다.
This restores the earbuds to the factory defaults.
TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.
Step 1

Follow the steps to connect and pair “JBL XXXX-LE” with the Google Assistant App, the name will depend on your model.
Once set up is complete, you will see the below screen:
Step 2

PLEASE NOTE: To verbally interact with your Google Assistant via the headphone, you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.


헤드폰과 통신하는 앱을 입수하는 데 문제를 겪고 있다면, (이미 헤드폰을 기기와 페어링한 상태로 가정) 통신 앱 오디오 설정으로 이동합니다. 거기서 해결책을 찾을 수 있는 가능성이 높습니다. 사용하고 있는 앱에서 헤드폰을 ‘통신 기기’로 설정해야 할 수 있습니다.
헤드폰과 통신하는 앱을 입수하는 데 문제를 겪고 있다면, (이미 헤드폰을 기기와 페어링한 상태로 가정) 통신 앱 오디오 설정으로 이동합니다. 거기서 해결책을 찾을 수 있는 가능성이 높습니다. 사용하고 있는 앱에서 헤드폰을 ‘통신 기기’로 설정해야 할 수 있습니다.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.

You can change the default assistant in the ‘My JBL Headphones’ app:
- Open the My JBL Headphones app on your device.
- Select the headphones you are connected too.
- Go to Settings by clicking the symbol in the top right corner.
- Select Voice Assistant.
- Now you can select your preferred voice assistant.

Your headphones may restart after switching Voice Assistant.