


JBL Tune 120TWS
제품 사양
General Specifications
Bluetooth version | 5.0 |
---|---|
Ear tip material | Silicon |
Driver size (mm) | 5.8 |
Audio Specifications
Driver sensitivity at 1kHz/1mW (dB) | 96 |
---|---|
Dynamic frequency response range (Hz) | 20Hz – 20kHz |
Impedance (ohms) | 14 |
Number of drivers per ear | 1 |
Dimension Specifications
충전케이스 무게 (온스) | 2.1 |
---|---|
이어폰 무게(온스) | 0.5 |
충전케이스 무게 (그램) | 60.1 |
이어폰 무게(그램) | 13.6 |
Control Connect Specifications
Bluetooth profiles | A2DP 1.3 AVRCP 1.5 HFP 1.6 |
---|---|
Bluetooth frequency | 2.402 GHz - 2.480 GHz |
Bluetooth transmitted modulation | GFSK, π/4DQPSK, 8DPSK |
Bluetooth transmitter power | 0 - 12dbm |
문서 및 다운로드
빠른 시작 안내
갤러리






비디오
박스 구성품
- TUNE120TWS
- 3가지 크기(S, M, L)의 이어팁
- 충전 케이블
- 품질보증서/경고 1부(W/!)
- QSG/안전 관리 지침 1부(S/i)

FAQ 및 사용 방법
If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.
If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.


깨끗한 면봉을 사용하여 알코올로 살짝 적셔서 다음을 수행합니다.
- 이어버드의 이어팁에서 귀지와 오염을 제거합니다.
- 이어버드와 충전 케이스에서 각각 충전 패드와 포트를 세척합니다. 그런 다음 부드럽고 물에 젖지 않은 상태의 마른 면직물을 사용하여 먼지와 보풀을 문질러 닦아냅니다.
- 충전 케이스의 뚜껑과 바닥의 홈을 세척합니다.
팁: 이러한 작업을 대략 몇 주마다 반복하여 헤드폰을 깨끗하게 유지함으로써 충전 속도와 품질에 영향을 주지 않도록 할 것을 권장합니다.
- Forget/unpair the headphones on your device.
- Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
- Pair the headphones to your device and see if this resolves the problem.
- If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
- Initiate a Product Reset to reset the earbud’s Bluetooth connection.
- Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
- Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
- Manually pair the 2 buds together again, as you did in step 2. This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
- Pair the buds to your Source Device.
때때로 충전이 중단될 수 있습니다. 충전이 아예 시작되지 않거나 이어 버드 한쪽의 전원이 갑자기 켜지고 페어링 절차가 시작되는 경우가 발생할 수 있습니다.
이는 거의 대부분 충전 접촉부의 오염이 원인입니다.
이러한 접촉부는 취약한데 땀, 피부 유분이나 귀지로 쉽게 오염될 수 있기 때문입니다.
대개 금도금이 되어 있으나, 금도금은 표면 오염을 막지는 못합니다.
충전 문제가 발생하면, 우선 각 이어 버드 양쪽과 충전 케이스의 모든 접촉부를 늘 깨끗하게 해야 합니다.
미세한 구멍까지 닿기는 쉽지 않을 수 있으나, 일반 면봉이나 메이크업용 면봉을 사용하면 됩니다. 끝을 소독용 알코올로 살짝 적신 다음, 각 접촉면에 가볍게 문질러서 닦아냅니다.
접촉부가 깨끗해 보일 때까지 반복하면, 충전이 제대로 작동됩니다.
드라이버(소프트웨어)가 다음과 같은 블루투스 프로토콜을 지원해야, 컴퓨터/PC/노트북에서 음악/소리를 재생할 수 있습니다.
• A2DP(고급 오디오 배포 프로필) 드라이버(사용자의 컴퓨터/PC/노트북에 음악 전송용).
• AVRCP(오디오/동영상 원격 제어 프로필) 드라이버(사용자의 기기에 대한 음악 건너뛰기/앞으로/일시정지/재생 명령 전송용)
반드시 사용자의 컴퓨터/PC/노트북용으로 제공되는 최신 드라이버 버전을 설치합니다.
올바른 드라이버(소프트웨어)를 다운로드하려면, 사용자의 컴퓨터/PC/노트북 제조업체의 웹사이트를 확인합니다. 일반적으로 ‘지원/다운로드’ 섹션에서 맞는 드라이버를 찾을 수 있습니다. 혹은, 해당 업체의 서비스 지원 센터에 연락하기를 권장합니다.
Microsoft/Windows 시스템에서 제공되는 표준 드라이버는 적합하지 않으며 오류 메시지가 표시되거나(PIN 코드를 입력해야 하는 등), 페어링이 작동하지 않습니다.


Use a clean cotton swab slightly moistened with alcohol to:
- Remove earwax and dirt from the ear tips on your earbuds.
- Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
- Clean the grooves on the cover and at the bottom of the charging case.
TIP: We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.
If the left ear pod is silent, please perform a new pairing with the right pod like shown in the quick-start guide.
Take them out of the charging case and click the center button on both the left and the right pod 3 times.
This forces a new pairing between the pods, and the left pod should automatically pair with the right pod from now on once you remove both pods from the charging case.
If you still cannot get the Left ear to play, please perform a factory reset by placing both pods in the charging case, while the charging case is charging. Now press the button on the right pod, and hold it for more than 5 seconds. You have now reset to factory settings. (Please note: If you have performed a factory reset, you will need to remove the headphones or "forget this device" from any smart phone or tablet they were once connected to. This will allow your device to now search for the newly restored headphones under BT devices)
The right pod is the primary, which is connected to your source, usually a smartphone.
The left pod is the secondary, which connects to the right pod.
헤드폰과 통신하는 앱을 입수하는 데 문제를 겪고 있다면, (이미 헤드폰을 기기와 페어링한 상태로 가정) 통신 앱 오디오 설정으로 이동합니다. 거기서 해결책을 찾을 수 있는 가능성이 높습니다. 사용하고 있는 앱에서 헤드폰을 ‘통신 기기’로 설정해야 할 수 있습니다.
헤드폰과 통신하는 앱을 입수하는 데 문제를 겪고 있다면, (이미 헤드폰을 기기와 페어링한 상태로 가정) 통신 앱 오디오 설정으로 이동합니다. 거기서 해결책을 찾을 수 있는 가능성이 높습니다. 사용하고 있는 앱에서 헤드폰을 ‘통신 기기’로 설정해야 할 수 있습니다.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.
The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:
• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.
• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device
Always get the latest driver version available for your Computer/PC/Laptop.
To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.
The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.
https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.