Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.

Yes. This headphone has a built in microphone. To answer a call, press the power button which is located on the Left Ear Cup for 1 second. If you wish to hang up the call, press and hold the power button for 2 seconds.

If the wireless mic is out of signal range, you will experience drop outs or no sound. Once range is reestablished, the speaker should automatically detect the mic and resume connection within less than 3 sec. 

When a wireless mic is connected, the speaker will play a notification sound once. If two wireless mics are connected at the same time, there may be a 1 sec gap between the two notification sounds. 

If one of the wireless mics is not working, we recommend the following: 

1. Turn off the speaker
2. Turn on the mic and place it on top of the speaker
3. Turn on the speaker
4. The speaker should automatically pair with the new mic within 3 min and play a notification sound 
 

Your JBL speaker is waterproof with IPX7 rating. (IPX7 means it can survive immersion in 1 meter/3.3 feet for up to 30 minutes.) To maintain the looks and functions of your speaker, please make sure to rinse it with fresh water after using it at a swimming pool or the ocean, then dry off all covers and areas where water can gather. The standard for waterproofing is for tap water. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the surface finish over time if not rinsed off after use.

Voice commands can only be triggered by the user who registered them during setup.

With some phones, such as iPhones and some Android models, volume is synchronized while Bluetooth is used, and levels below volume setting 6 (tested with iPhone 6 and iPhone 5s) and volume setting 5 on most Android devices will cause the GO to enter standby after some minutes. If you want to play softer while still using your iPhone as a source, please change to cabled connection from the headphone output to the AUX input of GO. This will make it possible for you to set the GO's volume at its minimum step, and then control total level on the telephone. Of course, if source level from the telephone is set extremely low, the GO will go into standby again, because GO needs a certain level to keep playing. Alternatively, use a phone which does not synchronize volume as source. Many Android phones do not synchronize volume, so by using such a phone, you can adjust GO to its lowest level, adjusting total level independently, even via Bluetooth. This will usually result in music volume at the desired level.

This headphone is supported by the My JBL Headphones App.

We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.

There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now. 

No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.

This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.

1. Ensure that your JBL One app device is less than 10m/33ft from the soundbar during the initial set-up.
2. Ensure your JBL soundbar is plugged into power and the power LED is illuminated on the BAR.
3. Unplug the power cord, wait 10 seconds, reconnect the power cord and allow the speaker to power up.
4. Temporarily relocate either the BAR or router so that they are closer together.  If the connection succeeds, the original location may be too far from the router to maintain a stable connection.
5. Try using a different device with the JBL ONE app installed and connected to your home network.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. If you're using the USB dongle, check that the correct playback device is selected under Control Panel > Sound > Playback. Select the proper playback device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Ensure that the correct device is selected as the default device under Control Panel>Sound>Playback. Make sure the on headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 600 or Quantum 800 Game, right-click, and select "Set as Default Device". Check your headset's game-chat balance dial and ensure that the balance is correct. Check the JBL Quantum 600 or Quantum 800 Game device and make sure it is not muted or turned all the way down.

The JBL Xtreme will no longer appear in the JBL Portable app while using Apple devices with iOS 14 or later installed, due to incompatibility. 
You can continue to use the speaker as normal with these devices through Bluetooth or Aux connection, but it will no longer appear in the app. 
There are currently no plans to release a new Firmware as the JBL Xtreme has been discontinued. 

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.

It is possible to pair two of the same model of JBL PartyBox speakers together through TWS (True Wireless Stereo) mode.

PartyBox On-The-Go/100:
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).

PartyBox 200/300/1000:
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.

Partybox 110/310/710/Encore/Essential:
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).

TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.

Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 and PartyBox 300 which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the Partybox 110, 310, 710 or Encore/Essential together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.

The JBL Quantum 350 Wireless headset is compatible via 2.4GHz wireless connection with:

• PC
• PlayStation
• Mac
• Nintendo Switch.

The JBL Quantum 100 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.

The JBL Quantum 200 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.

This product supports up to 10 hours of audio playtime. Please note that battery life may vary depending on volume level and content. 

Press and hold the power button located on the RIGHT ear cup. Make sure that the device is on and in Bluetooth range. If this is the first time connecting the device, it will automatically go into pairing mode. You will notice the LED light alternate between blue and white as it searches for a device to connect to. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect.

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.

QUANTUM ENGINE 

Software Update Release Notes 

Version 1.6.0.1053
Release Date: 1/21/21
 

1. Welcome feature has been implemented.

2. Surround Modes feature has been implemented.

3. ANC/TT toggle has been implemented.

4. The sidetone has been turned off by default for all models to avoid confusion.

5. QuantumSURROUND/QuantumSPHERE quality & performance have been improved.

6. Quantum 300 Mic Gain has been improved.

7. Quantum 800 FW update reliability has been improved.

8. Minor Bugs Fixed 

 

 

To skip the tracks forward, press and hold the volume up (+) button for 1-2 seconds and you will advanced to the next song. To start the current song you are listening to over, press and hold the volume down (-) button for 1-2 seconds. Please note: You can only advance to the next song be skipping forward, you cannot skip tracks backward. You can only restart the current song over by pressing the volume down (-) button.

To connect to a different Bluetooth device, first switch the headphones off. Now press and hold the center button on the headphone remote control for about 3-5 seconds. You should see the light blinking red/blue to indicate pairing mode, and the voice prompt should state “looking for device”. You should see "Reflect Mini 2" appear on the source's BT list. Choose that option, and wait for the voice prompt to state “connected”

To reset the headphones, power on the headphones and plug in the USB cable into a USB charger or USB port. Paired mobile devices should disconnect and the led should be constant white. When unplugging the USB cable, the headphones will power off. When manually powering on the headphones, and the last connected mobile phone is not in range, the headphones will revert to Bluetooth Pairing mode ( blue led will blink ) after 5 seconds.

If the screen appears dark, try repositioning the Horizon 2 for the light sensor to work to the fullest. In some positions, the Horizon 2 cannot effectively detect the ambient light level in the room. 

You can have your own Karaoke party with your JBL Partybox. Simply connect your Microphone (only included with the Partybox On The Go) and connect your mobile device over Bluetooth, then start playing music and sing along, it is that simple!

Please check that you have connected your android phone with JBL DRG before. Power off your Android phone and press the JBL DRG BT button to connect to another smartphone. If this is the case, please wait 3 minutes for JBL DRG to setup the Bluetooth connection with a new smartphone. This is because some android phones can’t send a “Disconnect” BT command to JBL DRG during power off, so JBL DRG need to wait until the Link is lost.

Switch the Soundgear ON. (If this is not possible, reset cannot be performed.)
Press and hold Volume + and Volume - simultaneously for longer than five seconds.
Soundgear switches OFF, and is now reset to factory settings.

The JBL Quantum 400 headset is compatible via 3.5mm jack with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
You can use the USB connection with PC, PS4, Nintendo Switch, and Mac.

The JBL Quantum 300 headset is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
You can also use the included USB dongle on PC, PlayStation and Mac.

This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

Switching to a new Wi-Fi network

1. Make sure your mobile device is connected to the same Wireless Network as your speaker.
2. Open your Google Home app 
3. Go to Settings 
4. Tap on Wi-FI Forget Network
   1. The current configuration is now forgotten.
5. In your Google Home app, you are forced back to the "Home Screen" and need to setup the device again.
6. Tap on
7. Find Add   Set up device Set up new devices in your home
8. Follow the instructions given to add the speaker to your Wi-Fi network.

Lost connection or changed settings

1. Open the Google Home app
2. On the home screen, tap on AddSet up device Set up new devices in your home
3. Follow the instruction provided.
   1. Remember that your current room name is the same as before, as well as other settings made for the speaker. You are only switching to a new Wi-Fi.
4. In addition, you can click on Discovery in the bottom menu of the Google Home app.
5. Tap on the Setup The Card information would show your old speaker name.  However, you can continue setting up the device following the instructions.

 

 

To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.

To activate TalkThru Technology, press the LEFT ear for a short press for 1 Second which allows you to clearly hear others for quick conversations without removing headphons. Music volume level should lower when TalkThru is engaged. Press again for 1 second to turn off Talk Thru.

If the audio is not centered to your monitor, then you can re-center your headset by doing the following: 1. Position yourself in front of your monitor. 2. Press the re-centering button on the side of your headset (button that looks like a circle) 3. The head-tracking sensor will start the automatic calibration.

This can be caused by the charge arm reaching its thermal temperature cutoff. This is a safety feature to prevent a potential risk. For proper heat dissipation, always be sure to have the charging arm in the open position when your smart phone is attached.

Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.

Common fixes:
(1) Make sure that the soundbar is not muted.
(2) Select the correct audio input source on the remote control.
(3) Check the connections to your TV or other devices
(4) Perform a reset if none of the above is working. 
(4.1) Press and hold VOL -, VOL +, and Source buttons to perform a reset.
 

When you press the power button you will hear a “door locked” tone. This means the top capacitive touch buttons have been locked. At this point you cannot trigger them. With another short press of the power button, you will hear a “door unlocked” tone, which means the top capacitive touch buttons have been unlocked.

If your volume level is quiet, make sure that the TalkThru is not activated on your headphones. In order to deactivate or activate TalkThru, quickly press the ANC button located at the top of the LEFT ear cup. You will hear an audible voice stating, TalkThru On when activated, and 'ANC On' when deactivated.

To pause/play music, tap center button on right or left ear for 1 second. To skip tracks forward, DOUBLE CLICK the center button on right or left ear. Unfortunately, you cannot skip tracks backward.

To skip tracks forward, double click the PAUSE/PLAY to advance to the next track. Please note: You can only skip tracks forward. This speaker does not have the capability to skip to the previous track.

Numbers 1-6 do NOT relate to ANC level, but you can find the optimal performance for your ears by selecting one of the bubbles. 

You can connect two of the same Partybox models (e.g. 2 x Partybox 310, or 2 x Partybox 100) together in TWS Mode by pressing and holding the Bluetooth button on both speakers for 5 seconds, or by pressing the dedicated TWS buttons on the rear panels of both speakers on the Partybox 110, 310 and 710. It is possible to pair two different Partybox models together using a wired connection (e.g. 1 x Partybox 310 and 1 x Partybox 100). It is also possible to pair two Partybox different models wirelessly in Party mode, however this is only possible with the newer Partybox models - the Partybox 110, 310 and 710. The Partybox 200 & 300 can be paired in TWS mode as they are the same model apart from the presence of a battery in the Partybox 300. If you connect an instrument or microphone to one Partybox speaker while using TWS, the instrument or microphone connected to one speaker will be reproduced by this speaker alone. You will not hear the instrument or microphone in both speakers. If it is necessary to have instruments reproduced by two or more PartyBox speakers, it is possible to use an RCA or aux cable – connected from the RCA, aux or daisy chain outputs on the speaker that the instrument or microphone is connected to, wired to the RCA, aux or daisy chain input of the secondary speaker. Alternatively a small mixing console can be used - connecting audio sources to this mixer and sending the mixed audio signal to the speakers with a wired connection.

To activate Ambient Aware DOUBLE CLICK the center button located on the LEFT ear. You should hear the music level drop. To resume to normal music level, DOUBLE CLICK the center button on LEFT ear again.

The UA Flash does not support AptX or AAC audio codecs

To take a phone call, press the center button of the RIGHT ear for 1 second. To hang up a call, press and hold the center button on the RIGHT ear for 1 second. To ignore a call, press and hold center button for 3 seconds until music resumes.

To charge the UA Flash, place inside charging case. While charging, both LEFT and RIGHT ear bud will display a sold red light. Once the headphones are fully charged. The red light will turn OFF. When the charging case is fully charged, the white LED's will light up accordingly: 0= 0% Dead 2-3 = 40%-50% 4=100% Full battery life

To pause/play music, press center button on RIGHT ear for 1 second. To skip tracks forward, DOUBLE CLICK the center button on RIGHT ear. Unfortunately, you cannot skip tracks backward.

To connect to a new device, begin with the headphones powered off and hold the center button on the RIGHT headphone for 5 seconds to enter pairing mode. You will hear the BT pairing audible chime as it searches for a different device. Make sure the device you are wanting to connect to is in range and BT is on. Once connected you will hear the audible Connected chime. Once Right ear is connected, press and hold the center button on LEFT ear for 3 seconds as it powers on and connects to the device followed by the same Connected audible chime.

To power on and pair the UA Flash, remove the ear tips from the charging case. If this is your first time using the headphones, they will automatically go into pairing mode. You will see the blue and red LED light flash on the RIGHT ear as it attempts to pair with your device. Make sure your device is in range and BT settings are ON. The JBL True Wireless Flash should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a slow blinking blue light below the UA logo on the RIGHT Ear. The RIGHT ear must be connected first in order to power on and connect the LEFT ear. To connect the LEFT ear, simply press and hold on the UA logo for 3-5 seconds until you hear the audible power on chime. (The left should automatically power on when you remove it from the case) Once powered on, it should connect to your device within a few seconds displaying a slow blinking blue LED light below the UA logo.

To reset, Long press the (Right) button for 2s when the earbuds in the case, the blue LED will flash once to indicate reset is done.

To activate Voice Assistant, press and hold the LEFT ear for 5 seconds until music stops and voice assistance asks what they can help you with

AmbientAware Technology allows you to hear your surroundings without removing your UA Pivot headphones. To activate AmbientAware mode, double press the Bionic Hearing button on the controller. You will hear a tone, and your music level will lower when AmbientAware Technology is engaged. To revert back to normal volume, simply double press the Bionic Hearing button again.

The UA Pivot headphones do not support AptX™ and AptX HD™ audio codecs.