How To
How To
448 results
-
You can connect two of the same Partybox models (e.g. 2 x Partybox 310, or 2 x Partybox 100) together in TWS Mode by pressing and holding the Bluetooth button on both speakers for 5 seconds, or by pressing the dedicated TWS buttons on the rear panels of both speakers on the Partybox 110, 310 and 710. It is possible to pair two different Partybox models together using a wired connection (e.g. 1 x Partybox 310 and 1 x Partybox 100). It is also possible to pair two Partybox different models wirelessly in Party mode, however this is only possible with the newer Partybox models - the Partybox 110, 310 and 710. The Partybox 200 & 300 can be paired in TWS mode as they are the same model apart from the presence of a battery in the Partybox 300. If you connect an instrument or microphone to one Partybox speaker while using TWS, the instrument or microphone connected to one speaker will be reproduced by this speaker alone. You will not hear the instrument or microphone in both speakers. If it is necessary to have instruments reproduced by two or more PartyBox speakers, it is possible to use an RCA or aux cable – connected from the RCA, aux or daisy chain outputs on the speaker that the instrument or microphone is connected to, wired to the RCA, aux or daisy chain input of the secondary speaker. Alternatively a small mixing console can be used - connecting audio sources to this mixer and sending the mixed audio signal to the speakers with a wired connection.Was this helpful? Thank you for your feedback!
-
Numbers 1-6 do NOT relate to ANC level, but you can find the optimal performance for your ears by selecting one of the bubbles.Was this helpful? Thank you for your feedback!
-
To skip tracks forward, double click the PAUSE/PLAY to advance to the next track. Please note: You can only skip tracks forward. This speaker does not have the capability to skip to the previous track.Was this helpful? Thank you for your feedback!
-
To pause/play music, tap center button on right or left ear for 1 second. To skip tracks forward, DOUBLE CLICK the center button on right or left ear. Unfortunately, you cannot skip tracks backward.Was this helpful? Thank you for your feedback!
-
If your volume level is quiet, make sure that the TalkThru is not activated on your headphones. In order to deactivate or activate TalkThru, quickly press the ANC button located at the top of the LEFT ear cup. You will hear an audible voice stating, TalkThru On when activated, and 'ANC On' when deactivated.Was this helpful? Thank you for your feedback!
-
When you press the power button you will hear a “door locked” tone. This means the top capacitive touch buttons have been locked. At this point you cannot trigger them. With another short press of the power button, you will hear a “door unlocked” tone, which means the top capacitive touch buttons have been unlocked.Was this helpful? Thank you for your feedback!
-
Common fixes:
(1) Make sure that the soundbar is not muted.
(2) Select the correct audio input source on the remote control.
(3) Check the connections to your TV or other devices
(4) Perform a reset if none of the above is working.
(4.1) Press and hold VOL -, VOL +, and Source buttons to perform a reset.
Was this helpful? Thank you for your feedback! -
Although the owner's manual states that owner can use this connector for home upgrade procedure, this is not so. The USB-connector used cannot be bought in commercially available cables, and the port must be considered for technician's use only.Was this helpful? Thank you for your feedback!
-
This can be caused by the charge arm reaching its thermal temperature cutoff. This is a safety feature to prevent a potential risk. For proper heat dissipation, always be sure to have the charging arm in the open position when your smart phone is attached.Was this helpful? Thank you for your feedback!
-
If the audio is not centered to your monitor, then you can re-center your headset by doing the following: 1. Position yourself in front of your monitor. 2. Press the re-centering button on the side of your headset (button that looks like a circle) 3. The head-tracking sensor will start the automatic calibration.Was this helpful? Thank you for your feedback!
-
To activate TalkThru Technology, press the LEFT ear for a short press for 1 Second which allows you to clearly hear others for quick conversations without removing headphons. Music volume level should lower when TalkThru is engaged. Press again for 1 second to turn off Talk Thru.Was this helpful? Thank you for your feedback!
-
To power on the headphones, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audio chime and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the T110BT headphone. Once you select that option, you will hear the confirmation tone. If you are trying to connect to a different device, turn the headphones on and press and hold for 3-5 seconds for the headphones to start searching for a different device. The headphones should appear on your discoverable devices within a few seconds. You should hear the audible tone and then the confirmation chime once it is connected. You will see the Bluetooth light alternate between red and blue when it is in pairing mode and then to a slow blinking LED blue light once it is connected to your device.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call us now at:
+855 15 512 512
NANO SOUND
+855 17 717 885
Email: Rottnaleang@gmail.com
Kfour Group Ltd.
078 88 72 82/ 069 82 87 82
Email: bunarong.kit@kfourgroup.com.kh