How To
How To
254 results
-
The owner's manual can be a bit difficult to understand. Here is what to do to program a preset station that has not already been saved in any preset: 1 Turn on the radio by clicking the FM button. 2 Find the station you want to save by doing what is shown under pt. 8 B or C, either clicking or pressing/holding for more than 2 seconds the left/right arrow buttons. 3 Press and hold the FM button for more than 2 seconds. Now the preset number appears blinking. 4 Click on the left/right arrow buttons to skip through the preset positions. 5 When you have located the desired memory preset position, such as Preset 4, confirm by clicking the FM button. Now the desired FM station is saved in memory preset 4. If you have already saved an FM station in a preset memory position, and want to have a new station placed there instead, here is what to do: 1 Turn on the radio by clicking the FM button. 2 Jump to the preset station you want to change with the round central button. Each click advances to the next preset. 3 When you are on the preset you want to change, e.g. preset 4, press and hold the FM button for more than 2 seconds. 4 The FM symbol and the frequency will now blink. 5 Before they stop blinking, click, or press and hold one of the arrow buttons to go through the FM frequencies step by step, or perform station search. 6 When you have found the new station you want to save in preset 4, click the round central button. 7 Now the new station is saved in preset 4.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.Was this helpful? Thank you for your feedback!
-
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.Was this helpful? Thank you for your feedback!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.Was this helpful? Thank you for your feedback! -
While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.Was this helpful? Thank you for your feedback!
-
The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.Was this helpful? Thank you for your feedback!
-
By pressing and holding the Bluetooth and the Volume PLUS buttons at the same time. The software version is shown in the display.Was this helpful? Thank you for your feedback!
-
You can listen up to 8 hours of MP3 music, with a fully charged battery, depending on volume and type of musicWas this helpful? Thank you for your feedback!
-
They support up to 8 paired devices without reset.Was this helpful? Thank you for your feedback!
-
You can connect 3 smart devices ( iOS or Android ) simultaneously by Bluetooth. One when connecting via AUX cable.Was this helpful? Thank you for your feedback!
-
You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.
Was this helpful? Thank you for your feedback! -
The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.Was this helpful? Thank you for your feedback!
-
You can clean it by wiping it gently with a damp cloth. Take extra care not to let water get into the speaker chamber, as it will damage the speaker drivers.
Was this helpful? Thank you for your feedback! -
With a short press of the dedicated Bluetooth button on the underside of the right ear cup, it powered on and enter the pairing mode.
Was this helpful? Thank you for your feedback! -
1. Open the Google Home app 2. Select the LINK VIEW 3. Select SETTINGS. 4. There is a line that says Paired Bluetooth Devices. 5. When you select it, it gives you the option to ENABLE PAIRING MODE. 6. Use your voice - "Hey Google, Open Bluetooth" and LINK VIEW will enable Bluetooth connection. You can disable Bluetooth using "Hey Google, Close Bluetooth" Once you have enabled Bluetooth pairing mode on your LINK VIEW, simply go into your Bluetooth settings menu on your mobile device and connect.Was this helpful? Thank you for your feedback!
-
To control the Light show on your JBL Partybox device, simply press the dedicated "Light show" button located under the Bluetooth icon. There are 3 different light shows available when toggling through them, select your favorite one and have a blast. There is no app developed to control or modify these settings, all settings have to be done on the Partybox device.Was this helpful? Thank you for your feedback!
-
Bluetooth Pairing
- Press the
button on the Partybox to start the pairing process.
- Grab your
device.
- Go to settings --> Bluetooth --> Enable Bluetooth -->
- Find the Partybox speaker you want to establish a Bluetooth connection to.
- You now have a successful connection and can stream your favorite music.
- NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
- To stop Bluetooth broadcasting then insert a USB device.
Was this helpful? Thank you for your feedback! - Press the
-
In Power On mode, press and hold 'Volume+' together with 'Play/Pause' for more than 2 seconds. The speaker will power off and is now reset.Was this helpful? Thank you for your feedback!
-
NOTE: Apple IOS users are not able to find their MAC address in Google Home app due to privacy policies in the USA and European market.
We advise setting up your device on a less secure network. Log into the router and retrieve the MAC address for your device then add it to your preferred network.Instructions below are for Android only
- Open your Google Home app
- Enable Bluetooth
on your device.
- Enable Location service
on your Android device.
- Remember to "Allow" Google Home to view your location while using the app (You are asked during setup of the Google Home app).
- In case you denied access go to Settings
Apps
- When you at selecting the Wi-Fi network from the list of available networks, before tapping on your network you need to get the MAC address.
- Tap the
located top right corner.
- In the pop-up menu press "Show MAC address"
- Tap the
You can now add the MAC address to your local Wireless router or system if your configuration requires this before installing the device on your network.Finding the MAC address after speaker is installed
- Open your Google Home app
.
- Tap on to view your home.
- Find your room
.
- In the top right corner tap Settings icon
.
- Scroll down to the bottom of the screen. You will see some system information and the MAC address as well.
Was this helpful? Thank you for your feedback! - Open your Google Home app
-
Finding the software version
- Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
- A voice will start prompting numbers which indicates the current software version.
Was this helpful? Thank you for your feedback! -
To perform a hardware reset of your earbuds, press and hold the reset button on the charging case* for more than 5 seconds. This resets the earbuds without restoring the settings to the factory defaults.
* Location
Live 300TWS/Live Pro+ TWS: Inside the charging case between the earbuds.
Live Free NC+/Reflect Mini NC TWS/Reflect Aero: On the back of the charging case, next to the USB-C port.
Club Pro+ TWS: On the bottom of the charging case, next to the USB-C port.Was this helpful? Thank you for your feedback! -
This video shows how to play music and much more with your Google Assistant. You can practice all of your voice commands on your Harman/Kardon Citation or JBL LINK products.
Was this helpful? Thank you for your feedback! -
USB Stick
- Get an empty
stick with speed of 2.0.
- Make sure it is formatted with FAT16 or FAT32.
- Your Music files can only be:
(32-320kbit/s),
(32-320kbit/s) and
(44.1K/48K/192K).
- The Partybox supports up to 8 subfolders.
- It will be played in alphabetic sequence with main folders first then subfolders.
- To skip songs forward, double press the Play/Pause button. To skip back, triple press the Play/Pause button.
Was this helpful? Thank you for your feedback! - Get an empty
-
Restore to factory settings:
In power ON mode, press and hold the Power Button for at least 10 seconds, until the volume and input selector lights begin to flash.
Reset to factory default includes Source, Volume settings, EQ settings, AirPlay name and Wi-Fi settings.Was this helpful? Thank you for your feedback! -
In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.Was this helpful? Thank you for your feedback!
-
In power ON mode press and hold the "Volume +" and "Play" buttons at the same time for more than 3 seconds -> Unit will power Off by itself. Now the unit is reset to factory default.Was this helpful? Thank you for your feedback!
-
Power on the JBL Pulse 3 For 5 seconds, press and hold the "Volume +" and "Play" buttons The JBL Pulse 3 will power off, and is now resetWas this helpful? Thank you for your feedback!
-
Press and hold the 'DAB/FM' & 'Preset 1' buttons for more than 2 seconds. The Horizon 2 is now reset to the default factory settings.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
To speak to our customer service specialist
1800-102-0525
Mon - Sun: 10:00 am - 7:00 pm (IST)
WhatsApp Us
Chat with a support agent via Whatsapp at:
by clicking https://bit.ly/2SfFSPh or send hi to 91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)