• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.

• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.

• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.

• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.

• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.

• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.

You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.

The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.

To check the firmware version:
Press and hold the 'Preset 1' & 'Preset 5' buttons for more than 10 seconds.

To find out the software version, press and hold the [VOL- ] and [SOURCE] buttons simultaneously.  The software version will scroll across the front display.
 

So your Pulse 4 got dirt on it, or even fingerprints, and you want to show off the device the best way possible.
Keep reading this article, and we will instruct you on how to clean the glass and device.

How to clean your speaker

• Dirt and stains on your speaker can be cleaned under lukewarm running tap water.
• Use a soft cloth, preferably cotton, to clean the glass and to remove fingerprints. Hold the top part to avoid adding more prints to the glass part.

Remember not to charge the device while it is still wet. The charging port needs to be completely dry before charging.

Contact our Customer support for more help and advice to keep your speaker top-notch!

Use a clean cotton swab slightly moistened with alcohol to:

1. Remove earwax and dirt from the ear tips on your earbuds.
2. Clean the charging pads and ports on your earbuds and in the charging case respectively. Then use a dry and soft cotton to rub down the dust and lint.
3. Clean the grooves on the cover and at the bottom of the charging case.

After cleaning, make sure the charging case and earbuds are dry before putting the earbuds back into the charging case.

TIP: We recommend that you repeat this operation every few weeks or so to keep your headphones clean and to not affect the charging speed and quality.

You can clean it by wiping it gently with a damp cloth. Take extra care not to let water get into the speaker chamber, as it will damage the speaker drivers.

Our FLIP 5 speaker is an "All-weather companion," and sometimes it can get dirt and other substances on it. Clean your speaker under lukewarm water from your water tap, and use a microfiber cloth to remove stains. Do not use any alcohol or other to remove stains and dirt. Do not charge your product while the charging port is wet; make sure it is dry before you connect it to a charger. Contact our Customer support if you need more advice.

With a short press of the dedicated Bluetooth button on the underside of the right ear cup, it powered on and enter the pairing mode.
 

1. Open the Google Home app 2. Select the LINK VIEW 3. Select SETTINGS. 4. There is a line that says Paired Bluetooth Devices. 5. When you select it, it gives you the option to ENABLE PAIRING MODE. 6. Use your voice - "Hey Google, Open Bluetooth" and LINK VIEW will enable Bluetooth connection. You can disable Bluetooth using "Hey Google, Close Bluetooth" Once you have enabled Bluetooth pairing mode on your LINK VIEW, simply go into your Bluetooth settings menu on your mobile device and connect.

To successfully connect the JBL Wireless Microphone Set to a Partybox, connect the supplied 6.3mm jack dongle to the Partybox's Microphone Input. Now turn on the dongle and the Partybox. The dongle's Power button light should stay lit, if the light turns off or does not stay lit it is off and needs to be charged with the provided USB cable.*

Now turn on one or both microphones as required and increase the Mic volume and gain to the desired level. The LED screen will show a channel number 'CH-1', 'CH-2', etc. The channel number is not changeable manually, and may change between power cycles, but all channels will connect automatically to the dongle. If the LED screens do not show a channel number, the batteries in the microphones need to be replaced.

*Charging the dongle while in use is not recommended and will likely cause unwanted interference.

You can enjoy streaming your favorite music over WiFi to your JBL BAR 9.1 Surround by adding it to your network. Turn on your soundbar. Download the Google Home app to your phone. Enable Bluetooth and Location services on your device. Open Google Home app Follow the instructions given in the app. You are now connected to your WiFi network and can enjoy streaming music to your system. The soundbar will now be able to automatically update, to make sure the performance is the best at all times.

You can enjoy streaming your favorite music over WiFi to your JBL BAR 5.1 Surround by adding it to your network.

Connecting to WiFi

• Turn on your soundbar.
• Download the Google Home app to your phone.
  • Available on Android and Apple.
• Enable Bluetooth, Location services on your Android device.
• Enable Bluetooth on your Apple device.
• Open Google Home app
• Follow the instructions given in the app.

You are now connected to your WiFi network and can enjoy streaming music to your system.

To control the Light show on your JBL Partybox device, simply press the dedicated "Light show" button located under the Bluetooth icon. There are 3 different light shows available when toggling through them, select your favorite one and have a blast. There is no app developed to control or modify these settings, all settings have to be done on the Partybox device.

Bluetooth Pairing

1. Press the button on the Partybox to start the pairing process.
2. Grab your device.
3. Go to settings --> Bluetooth --> Enable Bluetooth -->
4. Find the Partybox speaker you want to establish a Bluetooth connection to.

        

5. You now have a successful connection and can stream your favorite music.
   1. NOTE: It is only possible to have two devices connected at the same time and if you want to listen through the second Bluetooth device then stop the current one from playing and use the second device.
   2. To stop Bluetooth broadcasting then insert a USB device.

In Power On mode, press and hold 'Volume+' together with 'Play/Pause' for more than 2 seconds. The speaker will power off and is now reset.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

NOTE: Apple IOS users are not able to find their MAC address in Google Home app due to privacy policies in the USA and European market.

We advise setting up your device on a less secure network. Log into the router and retrieve the MAC address for your device then add it to your preferred network.

Instructions below are for Android only

1. Open your Google Home app 
2. Enable Bluetooth  on your device.
3. Enable Location service  on your Android device.
   1. Remember to "Allow" Google Home to view your location while using the app (You are asked during setup of the Google Home app).
   2. In case you denied access go to Settings  Apps  Google Home  Permissions  Allow to view Location.
4. When you at selecting the Wi-Fi network from the list of available networks, before tapping on your network you need to get the MAC address.
   1. Tap  the  located top right corner.
   2. In the pop-up menu press "Show MAC address" Write down the MAC Address.

You can now add the MAC address to your local Wireless router or system if your configuration requires this before installing the device on your network.

Finding the MAC address after speaker is installed

1. Open your Google Home app .
2. Tap on  to view your home.
3. Find your room .
4. In the top right corner tap Settings icon .
5. ​Scroll down to the bottom of the screen. You will see some system information and the MAC address as well.

Finding the software version

1. Press and hold the 'Volume-' and 'Bass Boost' buttons for 5 seconds.
2. A voice will start prompting numbers which indicates the current software version.

Playing local playlist that you created via Spotify works differently for Android TV system, which the LINK BAR has built-in!

Here is how to do it:

1. Go to the Google Play Store on your TV screen (Use remote to navigate).
2. Download the Spotify app
3. Sign-in with your account.
4. You can use the dedicated app and navigate through your playlist.
5. Alternatively, you can now use voice commands such as "Ok Google, Play my Playlist Sunday Funday On Spotify"

Now you can enjoy Spotify using voice or the Remote Control.

*Some commands may not be available in all countries.

JBL TOUR ONE
Power off Tour One first and hold the ambient aware button on the left earcup for 2 seconds. You can get ANC on without Bluetooth connection, which will save your battery. Once you slide up the button on the right ear cup to power on, Bluetooth connection and music will return to normal.

 

JBL TOUR PRO+ TWS
Press and hold both right and left earbuds on Tour Pro+ TWS for 5 seconds at the same time. You can get ANC on without Bluetooth connection, which will save your battery. Once you press and hold both right and left earbuds for 5 seconds, Bluetooth connection and music will return to normal.

 

1. Press and hold the [VOL- ] and [SOURCE] buttons simultaneously.  The software version will scroll across the front display.
2. If a newer software version is available, download it from the JBL website.
3. Copy the two files to the Root directory of an empty USB thumb drive.
   • Update.zip
   • Checksum.txt
4. On the bar, press and hold the [POWER] and [SOURCE] buttons for more than 10 seconds.  This will reset the BAR 5.1 Surround.
5. Insert the USB thumb drive into the USB port on the rear panel of the bar.
6. On the bar, press and hold the [POWER] and [VOL-] buttons for more than 10 seconds to begin the software update process.
7. "UPDATING" will appear on the front display of the bar.
8. Wait for the software update to complete.  The unit will reboot and go back to standby.
9. Turn unit on.
10. Press and hold the [VOL- ] and [SOURCE] buttons simultaneously.  The new software version will scroll across the front display.

We included a Remote Control in your box (I know, that's sweet of us), and you need to pair it with your LINK BAR before it is working.

This is how you will do it

1. Press the BLUETOOTH button on the LINK BAR
2. Now hold the BLUETOOTH button down for 3-5 seconds.
3. When you see "SEARCHING FOR ACCESSORIES" on your TV screen, release the BLUETOOTH button.
4. On your REMOTE press the HOME and BACK buttons at the same time.
5. A Green LED light will flash on the REMOTE to indicate that it is in pairing mode.
6. Keep holding down the buttons until you see a message on the TV screen that says, "Pairing remote control to LINK BAR" After 10 seconds, release.
7. If done successfully on your TV screen, you will see an indicator counting down that it will "pair" with your remote.

Enjoy your entertainment with few clicks away!

BONUS TIP:  There is an Android app called Android TV that will turn your Smartphone into a Remote controller.