How To
How To
909 results
-
This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.Was this helpful? Thank you for your feedback!
-
It is usually not necessary to replace an unresponsive remote control. First, check to see if there is a small plastic tab extending out of the base of the remote control. This is a protective sleeve installed on new remote controls to prevent the battery from draining. Pull this tab to remove the plastic sleeve. The sleeve must be removed before the remote will operate. If the sleeve was removed or not present and the remote control is not working then a new battery should be installed before replacing the remote control. There is a small slide out drawer that houses the battery. The battery type will be either CR2025 or CR2032 for remotes of this size. Replacement batteries are commonly available from most electronic and convenience stores that sell small batteries. Check the number on the original battery and replace it with a battery that uses the same number. These steps will typically solve the problem.Was this helpful? Thank you for your feedback!
-
No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.Was this helpful? Thank you for your feedback!
-
There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now.Was this helpful? Thank you for your feedback!
-
No, your subwoofer is not defective at all! This is normal and by design of the product after it has been paired for a longer period of time.Was this helpful? Thank you for your feedback!
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
Sounds like your JBL LINK 10 or LINK 20 has been connected to another Wi-Fi network. It is very simple to reconnect to your Wi-Fi by using the Google Home app. Simply select your Wi-Fi in the app, and you're all set. All information about the speaker and voice teaching is stored in the Cloud, so you do not have to do this again.Was this helpful? Thank you for your feedback!
-
To install your JBL LINK speaker using Apple iOS... 1. Download the Google Home app. 2. Activate your Bluetooth connection, as it is required for Apple devices. 3. Follow the instructions in the Google Home app.Was this helpful? Thank you for your feedback!
-
This headphone is supported by the My JBL Headphones App.Was this helpful? Thank you for your feedback!
-
Some of the DJ EQ curves have been removed from the My JBL Headphones app. Harman will ‘continuously’ update the My JBL Headphones app with new DJ sound-curves as this number changes based on who we sign agreements with and when.
See the release notes for app version 4.10.9 below:
- Adding support for TOUR PRO+ TWS and TOUR ONE Global version
- Removing expired DJ’s signaturesWas this helpful? Thank you for your feedback! -
With some phones, such as iPhones and some Android models, volume is synchronized while Bluetooth is used, and levels below volume setting 6 (tested with iPhone 6 and iPhone 5s) and volume setting 5 on most Android devices will cause the GO to enter standby after some minutes. If you want to play softer while still using your iPhone as a source, please change to cabled connection from the headphone output to the AUX input of GO. This will make it possible for you to set the GO's volume at its minimum step, and then control total level on the telephone. Of course, if source level from the telephone is set extremely low, the GO will go into standby again, because GO needs a certain level to keep playing. Alternatively, use a phone which does not synchronize volume as source. Many Android phones do not synchronize volume, so by using such a phone, you can adjust GO to its lowest level, adjusting total level independently, even via Bluetooth. This will usually result in music volume at the desired level.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
8:30 am - 6:30 pm (IST)
WhatsApp Us
Chat with a support agent via Whatsapp at:
by clicking https://bit.ly/2SfFSPh or send hi to 91 70658 44446
Mon - Sun: 8:30 am - 6:30 pm (IST)