How To
How To
264 results
-
Was this helpful? Thank you for your feedback!
-
It is very simple to connect to your Car with the JBL Partybox 200 or 300. Use the included cable that connects through the cigarette connector in your Car and power on the Partybox! Please note that the 12V connection does not charge the battery in the Partybox 300 - it will only power the Partybox when in use. To charge the battery, it will have to be plugged into AC power ( 110 - 230V )Was this helpful? Thank you for your feedback!
-
It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.
If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
Repeat until the contact points are visibly clean, and charging should work as designed.
Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all TWS earphones and cases.Was this helpful? Thank you for your feedback! -
To charge the headphones, place inside charging case. While charging, both LEFT and RIGHT ear bud will display a sold red light. Once the headphones are fully charged. The red light will turn OFF. When the charging case is fully charged, the white LED's will light up accordingly. Battery life can last for 10-hours per charge. You may recharge your earphones for another 40-hours playtime with the charging case. It takes 2 hours to fully charge the charing case.Was this helpful? Thank you for your feedback!
-
No. Bluetooth does not work under water. The Endurance DIVE however has a built-in MP3 player for music, and is IPX7 waterproof. This means you can use the headphones submerged to 1 meter depth, up to 30 minutes at a time. Also note that for normal swimming, you won't be submerged all the time, so the headphones should be waterproof for the duration of your swim.Was this helpful? Thank you for your feedback!
-
Yes. To take a call from the Live 200BT press the center button located on the RIGHT neckband for 1-2 seconds. To hang up, simply press the center button again.Was this helpful? Thank you for your feedback!
-
Yes. A built-in microphone combined with a patented echo cancellation system secures clear and easy phone conversation. If a phone call is received while listening to music just push play button to answer the call. No need to find or touch the phone. This hands-free functionality can even be used for phone conferencesWas this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up for 2-3 seconds and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. Once connected, you will see a solid blue light above the power button.Was this helpful? Thank you for your feedback!
-
Because bluetooth cannot travel through water, the only Endurance model that is used for swimming is the Endurance DIVE model. The Endurance DIVE model features an MP3 player which allows you to listen to music under water without using bluetooth. Furthermore, only DIVE features a function lock, which prevents water from activating functions inadvertently. SPRINT and JUMP do not have this lock function, and will not work under water.Was this helpful? Thank you for your feedback!
-
The JBL Endurance SPRINT, JUMP and DIVE can be used in salt water (i.e. sea) but we recommend to thoroughly wash the headphones in fresh water after every use in salt water, to remove the salt residue. Please note that only DIVE can actually be used in water, because it features a function lock and a built-in memory for MP3 music files. SPRINT and JUMP cannot be used in water, because the touch buttons will malfunction when submerged, and Bluetooth cannot function at all under water.Was this helpful? Thank you for your feedback!
-
The headphones can pair to multiple devices but can only be connected to one device at a time.Was this helpful? Thank you for your feedback!
-
Yes, you can use your Soundgear for TV watching or playing video games. You can use the TV speakers and the Soundgear simultaneously, they will be synchronized in time.Was this helpful? Thank you for your feedback!
-
Yes, all sources that output analog stereo line-level signals or stereo audio optical digital signals may be used, cable-connected to the BTA 20 transmitter. Digital signals must be in PCM format. So if you have a CD player or an FM radio, you can connect the BTA 20 to it, and transmit to your Soundgear (or to other Bluetooth headphones that support the format). Please note that record players need an additional preamplifier to work this way. Of course a TV set can be connected as well, either via optical digital PCM output, via line outputs or via headphone output.Was this helpful? Thank you for your feedback!
-
The JBL Quantum 800 can only be used via a 3.5mm, Bluetooth, or 2.4Ghz wireless connection.Was this helpful? Thank you for your feedback!
-
The Game-Chat balance dial only works when your headset is powered on. Please note that it supports connection with a USB Type A to C cable and a wireless transmitter dongle, but doesn’t support connection through a 3.5mm cable or Bluetooth for mobile games.Was this helpful? Thank you for your feedback!
-
Yes, you can activate the noise reduction circuits alone, with no connection to a source device by Bluetooth or cable. The headphones will stay on as long as there is power in the battery, which is close to 30 hours for pure NC function. Please note that there is a slight residual noise from the NC system, which will be drowned out by music playing, or by surrounding noise such as airplane noise. If you use the NC in surroundings that are near quiet to begin with, you may not get an improvement in noise level.Was this helpful? Thank you for your feedback!
-
Yes, you do not need to have music playing to keep the noise cancelling switched on. There may be a slight residual hiss from the NC system, which would usually be masked by music, but there will still be a significant reduction of external noise.Was this helpful? Thank you for your feedback!
-
Yes, that’s the best part about this speaker, there are so many options. Besides streaming over Wi-Fi, the JBL Control Xstream also offers a Bluetooth connection and an AUX inputWas this helpful? Thank you for your feedback!
-
Yes, from within the JBL Connect App, when you have 2 JBL Boombox speakers connected, set them in Stereo Mode. When you add a 3rd ( or more ) JBL Boombox speakers, they will automatically revert back to Party modeWas this helpful? Thank you for your feedback!
-
Yes, Control Xstream is a Chromecast device that allows you to cast music content via your Chrome browser. However, the JBL Control Xstream is not made for video purposes, because there will be delay between sound and image.Was this helpful? Thank you for your feedback!
-
The JBL Quantum Stream Studio comes with an adapter that can be mounted on different boom mic arm systems or tripods. The adapter is already built in the microphone stand so that you always have the adapter close to you when needed.
Was this helpful? Thank you for your feedback! -
Please note that although the Control Xstream does have a threaded insert for brackets, JBL offers no brackets. Custom made wallmounts should be used.Was this helpful? Thank you for your feedback!
-
Yes, the JBL Playlist can be reset to factory settings. First, Power ON the JBL Playlist. Secondly, press and hold the Play and Volume (-) buttons simultaneously for about 10 seconds, and after 10 seconds you should see the Play/Pause and Bluetooth button light up, followed by the speaker going into Standby. Once you see the speaker powers back ON, reset is complete.Was this helpful? Thank you for your feedback!
-
No, Soundgear is wireless Bluetooth only, and needs to be charged to play music. But the BTA 20 transmitter must of course be connected with a cable to the signal source.Was this helpful? Thank you for your feedback!
-
Yes, Control Xstream uses both 2.4 GHz and 5 GHZ wi-fi networks.Was this helpful? Thank you for your feedback!
-
No, it's not possible to connect simultaneously from multiple devices to the Flip 3 SE. If you need a new device to pair with the Flip 3 SE, please press the Bluetooth button the Flip 3 SE to enable pairing mode. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tabletWas this helpful? Thank you for your feedback!
-
No. The two Soundgears can connect to the BTA, but not to each other. Also, when using one Soundgear, the use of aptxLL may result in a delay. If you are connected to two, the delay may be more noticeable, since LL is no longer active.Was this helpful? Thank you for your feedback!
-
No, for now it is only possible to connect two speakers together using the JBL connect feature. Newer JBL products feature JBL Connect+, which allows you to connect > 100 devices simultaneously, these however are not compatible with older JBL products featuring JBL ConnectWas this helpful? Thank you for your feedback!
-
While you have an incoming call, and you can hear the call-tone from your SoundGear, simply adjust the SoundGear's call-tone level to the desired intensity, using the SoundGear's volume buttons.Was this helpful? Thank you for your feedback!
-
Yes, if a telephone is connected via Bluetooth to Horizon, this is possible. When adjusting the wake-up timer, there will be an option to select various wake-up tones, or Bluetooth sound. Select Bluetooth as source, while the telephone is playing the music stored locally, or streaming what you want as wake-up music. When the wake-up adjustment is finished, music will be playing over Bluetooth through the Horizon. Press Pause on the source telephone, or press the round selector button (between the two arrow-buttons) on the Horizon to pause the music. Now the system is ready to wake you up with Bluetooth music. When wake-up time arrives, Horizon sends a Play command to the telephone, and music plays via Bluetooth. You can use music that is stored in the phone, use Spotify or play from the cloud. This has been tested with both iPhone 6 and Samsung S6, and should work flawlessly.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
To speak to our customer service specialist
1800-102-0525
Mon - Sun: 10:00 am - 7:00 pm (IST)
WhatsApp Us
Chat with a support agent via Whatsapp at:
by clicking https://bit.ly/2SfFSPh or send hi to 91 70658 44446
Mon - Sun: 10:00 am - 7:00 pm (IST)