



JBL Quantum 800
Product Specifications
General Specifications
Bluetooth version | 5.0 |
---|---|
Driver size (mm) | 50 |
Audio Specifications
Driver sensitivity at 1kHz/1mW (dB) | 95 |
---|---|
Dynamic frequency response range (Hz) | ["20 Hz - 40 kHz (Passive)", "20 Hz - 20 kHz (Active)"] |
Impedance (ohms) | 32 |
Dimension Specifications
Weight (g) | 410 |
---|---|
Weight (oz) | 14.5 |
Headphone Cable Length (m) | 1.5 |
Headphone Cable Length (ft) | 4.9 |
Ear Cup External Height (in) | 3.8 |
Ear Cup External Width (in) | 3.4 |
Ear Cup Internal Height (in) | 2.4 |
Ear Cup Internal Width (in) | 1.7 |
Ear Cup Depth (in) | 1.1 |
Ear Cup External Height (cm) | 9.7 |
Ear Cup External Width (cm) | 8.7 |
Ear Cup Internal Height (cm) | 6.2 |
Ear Cup Internal Width (cm) | 4.2 |
Ear Cup Depth (cm) | 2.7 |
Control Connect Specifications
Bluetooth profiles | A2DP 1.3, HFP 1.6 |
---|---|
Bluetooth frequency | 2.402 GHz - 2.480 GHz |
Bluetooth transmitted modulation | GFSK, /4π DQPSK, 8DPSK |
Bluetooth transmitter power | <9 dBm |
Documents & Downloads
Spec Sheets
Manuals
Quick Start Guide
Gallery










Videos
What’s in the Box
- 1 x JBL Quantum 800 headset
- 1 x USB Charging Cable
- 1 x 3.5 mm audio cable
- 1 x USB wireless dongle
- 1 x Windshield foam for microphone
- 1 x Quick Start Guide
- 1 x Warranty card
- 1 x Safety Sheet

FAQs & How-Tos
-
How to use your Quantum wirelessly
It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone. Was this helpful? Thank you for your feedback!
-
How to set up your microphone
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.
How to check your PC settings for the correct recording device
1. Go to Control Panel
2. Select Hardware and Sound
3. Click on Sound
3 Select Recording
4. Make sure to select the proper recording device.-
Right-click on it Quantum headset.
-
Now select "Set Default Device" or Select "Default Communication Device"
5. Check the microphone levels by right-click on your Quantum headset. Then click on Properties
6. Choose Levels.
7. Adjust accordingly.Was this helpful? Thank you for your feedback!
-
-
How do I request or purchase peripheral parts for my JBL Quantum headset?
Replacement parts are available from authorized dealers and Service Centers. Please contact our customer service department for more information and contact details.
Was this helpful? Thank you for your feedback!
-
How to avoid WiFi interference for your headphone
You might have to add a USB extension dock to get the JBL Quantum 350/600/800/810 dongle as close to the headset, or place the common sources of interference (e.g. routers, Wi-Fi speakers etc.) as far from the JBL Quantum 350/600/800/810 dongle.
Was this helpful? Thank you for your feedback!
-
Why are my headphones shown as “speakers” on Windows?
The “Speaker” mode allows the JBL QuantumENGINE to receive more than two channels of audio. It also prevents some applications from adding extra signal processing intended for other headphones, which would negatively impact the performance of the JBL QuantumSURROUND or JBL QuantumSPHERE 360 technology.
Was this helpful? Thank you for your feedback!
-
How to switch between Active Noise Cancelling and TalkThru
Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.Was this helpful? Thank you for your feedback!
-
How to charge your Quantum headphone
The battery is charged using an included USB-A to USB-C USB fabric cable. It will be fully charged for 2 hrs. Note, this cable is only for charging the battery, it will not deliver audio.Was this helpful? Thank you for your feedback!
-
Can I use the JBL Quantum 800 in USB mode
The JBL Quantum 800 can only be used via a 3.5mm, Bluetooth, or 2.4Ghz wireless connection.Was this helpful? Thank you for your feedback!
-
No sound when playing or listening to music
Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 600 or Quantum 800 Game, right-click, and select "Set as Default Device". Check your headset's game-chat balance dial and ensure that the balance is correct. Check the JBL Quantum 600 or Quantum 800 Game device and make sure it is not muted or turned all the way down.
Was this helpful? Thank you for your feedback!
-
Which products are supported by the JBL QuantumENGINE software?
JBL Quantum 300, 350, 400, 600, 610, 800, 810 ONE, TWS and Stream are working with the QuantumENGINE
Was this helpful? Thank you for your feedback!
-
Why you can't hear your teammates
Make sure JBL Quantum 800 is selected for PC.
If you are connected to the PC via USB, check that the default device is selected under Control Panel --> Sound --> Playback./>
Select JBL Quantum 800, right-click and "Set as default device".
Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume.
Check that your headset's GAME-CHAT balance dial and ensure that the balance is correct, you might refer to the screenshot below from the QuantumENGINE PC software.
If you still cannot hear the game or music audio, or if the volume is still very low, check if the TalkThrough is activated via the QuantumENGINE software.
Or you can turn it off by short pressing on the Smart Ambient button on the headset.
Was this helpful? Thank you for your feedback!
-
What's in the box
Your JBL Quantum 600 and Quantum 800 includes the headset, a USB Type-A to C cable, 3.5mm cable, a wireless transmitter dongle, QSG l Warranty Card l Warning Card, and a microphone windshield.
Was this helpful? Thank you for your feedback!
-
The story behind our Quantum name
We wanted the name to reflect this futuristic inspiration married with cutting-edge technology. The Quantum name was ultimately chosen as it conjures images of both the technology aspect through the advances in quantum computing but also a very organic feel with reference to quantum physics and the science behind building upon small elements to make massive improvements.
Was this helpful? Thank you for your feedback!
-
Mic Monitoring Support
Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.Was this helpful? Thank you for your feedback!
-
How to connect a Bluetooth device
With a short press of the dedicated Bluetooth button on the underside of the right ear cup, it powered on and enter the pairing mode.
Was this helpful? Thank you for your feedback!
-
What can you do with JBL QuantumENGINE software?
You can adjust equalizer, RGB LED effects, change microphone settings and update the headset's firmware.Was this helpful? Thank you for your feedback!
-
Purchase parts for Quantum headphones
Replacement parts are available from authorized dealers and Service Centers. Please contact our JBL customer service department for more information and contact details.Was this helpful? Thank you for your feedback!
-
How to clean your Quantum headphone
You can clean your headphones by wiping it gently with a damp cloth. Take extra care not to let water get into the speaker chamber, as it will damage the speaker drivers. If you need replacement ear pads, please reach out to your local JBL Customer Support to inquire about replacement parts. Was this helpful? Thank you for your feedback!
-
Physical damage on headphones
If your JBL Quantum headphone is under warranty, you can visit our Support Site at
Was this helpful? Thank you for your feedback!
-
Does the Quantum headphone support the Mic monitoring feature?
Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. And the default setting of the mic monitoring is set of “OFF”. Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
To speak to our customer service specialist
1800-102-0525
Mon - Sun: 10:00 am - 7:00 pm (IST)