How To
How To
-
Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. And the default setting of the mic monitoring is set of “OFF”.
Was this helpful? Thank you for your feedback! -
Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.Was this helpful? Thank you for your feedback!
-
Yes. This headphone has a built in microphone. To answer a call, press the power button which is located on the Left Ear Cup for 1 second. If you wish to hang up the call, press and hold the power button for 2 seconds.Was this helpful? Thank you for your feedback!
-
If the wireless mic is out of signal range, you will experience drop outs or no sound. Once range is reestablished, the speaker should automatically detect the mic and resume connection within less than 3 sec.
When a wireless mic is connected, the speaker will play a notification sound once. If two wireless mics are connected at the same time, there may be a 1 sec gap between the two notification sounds.
If one of the wireless mics is not working, we recommend the following:
1. Turn off the speaker
2. Turn on the mic and place it on top of the speaker
3. Turn on the speaker
4. The speaker should automatically pair with the new mic within 3 min and play a notification sound
Was this helpful? Thank you for your feedback! -
Your JBL speaker is waterproof with IPX7 rating. (IPX7 means it can survive immersion in 1 meter/3.3 feet for up to 30 minutes.) To maintain the looks and functions of your speaker, please make sure to rinse it with fresh water after using it at a swimming pool or the ocean, then dry off all covers and areas where water can gather. The standard for waterproofing is for tap water. Chemicals and salt in your pool or the ocean can damage the waterproof seals or harm the surface finish over time if not rinsed off after use.Was this helpful? Thank you for your feedback!
-
Voice commands can only be triggered by the user who registered them during setup.Was this helpful? Thank you for your feedback!
-
With some phones, such as iPhones and some Android models, volume is synchronized while Bluetooth is used, and levels below volume setting 6 (tested with iPhone 6 and iPhone 5s) and volume setting 5 on most Android devices will cause the GO to enter standby after some minutes. If you want to play softer while still using your iPhone as a source, please change to cabled connection from the headphone output to the AUX input of GO. This will make it possible for you to set the GO's volume at its minimum step, and then control total level on the telephone. Of course, if source level from the telephone is set extremely low, the GO will go into standby again, because GO needs a certain level to keep playing. Alternatively, use a phone which does not synchronize volume as source. Many Android phones do not synchronize volume, so by using such a phone, you can adjust GO to its lowest level, adjusting total level independently, even via Bluetooth. This will usually result in music volume at the desired level.Was this helpful? Thank you for your feedback!
-
This headphone is supported by the My JBL Headphones App.Was this helpful? Thank you for your feedback!
-
We are sorry about this problem. EuP regulations require that electronics go into full off after some time. Unfortunately, this means that the soundbar cannot be woken up again after half an hour. It is necessary to use the ON/OFF switch.Was this helpful? Thank you for your feedback!
-
There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now.Was this helpful? Thank you for your feedback!
-
No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.Was this helpful? Thank you for your feedback!
-
This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.Was this helpful? Thank you for your feedback!
-
- Ensure that your JBL One app device is less than 10m/33ft from the soundbar during the initial set-up.
- Ensure your JBL soundbar is plugged into power and the power LED is illuminated on the BAR.
- Unplug the power cord, wait 10 seconds, reconnect the power cord and allow the speaker to power up.
- Temporarily relocate either the BAR or router so that they are closer together. If the connection succeeds, the original location may be too far from the router to maintain a stable connection.
- Try using a different device with the JBL ONE app installed and connected to your home network.
Was this helpful? Thank you for your feedback! -
Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. If you're using the USB dongle, check that the correct playback device is selected under Control Panel > Sound > Playback. Select the proper playback device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.
Was this helpful? Thank you for your feedback! -
Ensure that the correct device is selected as the default device under Control Panel>Sound>Playback. Make sure the on headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.Was this helpful? Thank you for your feedback!
-
Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.Was this helpful? Thank you for your feedback!
-
Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 600 or Quantum 800 Game, right-click, and select "Set as Default Device". Check your headset's game-chat balance dial and ensure that the balance is correct. Check the JBL Quantum 600 or Quantum 800 Game device and make sure it is not muted or turned all the way down.
Was this helpful? Thank you for your feedback! -
The JBL Xtreme will no longer appear in the JBL Portable app while using Apple devices with iOS 14 or later installed, due to incompatibility.
You can continue to use the speaker as normal with these devices through Bluetooth or Aux connection, but it will no longer appear in the app.
There are currently no plans to release a new Firmware as the JBL Xtreme has been discontinued.Was this helpful? Thank you for your feedback! -
In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).
The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:
• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.
• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device
Always get the latest driver version available for your Computer/PC/Laptop.
To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.
The standard drivers provided by Microsoft/Windows system are not correct and will result in error messages (such as having to enter a PIN code), or pairing will not work.Was this helpful? Thank you for your feedback! -
It is possible to pair two of the same model of JBL PartyBox speakers together through TWS (True Wireless Stereo) mode.
PartyBox On-The-Go/100:
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).
PartyBox 200/300/1000:
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.
Partybox 110/310/710/Encore/Essential:
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).
TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.
Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 and PartyBox 300 which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the Partybox 110, 310, 710 or Encore/Essential together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.Was this helpful? Thank you for your feedback! -
The JBL Quantum 350 Wireless headset is compatible via 2.4GHz wireless connection with:
- PC
- PlayStation
- Mac
- Nintendo Switch.
Was this helpful? Thank you for your feedback! -
The JBL Quantum 100 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
Was this helpful? Thank you for your feedback! -
The JBL Quantum 200 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.
Was this helpful? Thank you for your feedback! -
This product supports up to 10 hours of audio playtime. Please note that battery life may vary depending on volume level and content.Was this helpful? Thank you for your feedback!
-
Press and hold the power button located on the RIGHT ear cup. Make sure that the device is on and in Bluetooth range. If this is the first time connecting the device, it will automatically go into pairing mode. You will notice the LED light alternate between blue and white as it searches for a device to connect to. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
QUANTUM ENGINE
Software Update Release Notes
Version 1.6.0.1053
Release Date: 1/21/21
-
Welcome feature has been implemented.
-
Surround Modes feature has been implemented.
-
ANC/TT toggle has been implemented.
-
The sidetone has been turned off by default for all models to avoid confusion.
-
QuantumSURROUND/QuantumSPHERE quality & performance have been improved.
-
Quantum 300 Mic Gain has been improved.
-
Quantum 800 FW update reliability has been improved.
-
Minor Bugs Fixed
Was this helpful? Thank you for your feedback! -
-
To skip the tracks forward, press and hold the volume up (+) button for 1-2 seconds and you will advanced to the next song. To start the current song you are listening to over, press and hold the volume down (-) button for 1-2 seconds. Please note: You can only advance to the next song be skipping forward, you cannot skip tracks backward. You can only restart the current song over by pressing the volume down (-) button.Was this helpful? Thank you for your feedback!
-
To connect to a different Bluetooth device, first switch the headphones off. Now press and hold the center button on the headphone remote control for about 3-5 seconds. You should see the light blinking red/blue to indicate pairing mode, and the voice prompt should state “looking for device”. You should see "Reflect Mini 2" appear on the source's BT list. Choose that option, and wait for the voice prompt to state “connected”Was this helpful? Thank you for your feedback!
-
To reset the headphones, power on the headphones and plug in the USB cable into a USB charger or USB port. Paired mobile devices should disconnect and the led should be constant white. When unplugging the USB cable, the headphones will power off. When manually powering on the headphones, and the last connected mobile phone is not in range, the headphones will revert to Bluetooth Pairing mode ( blue led will blink ) after 5 seconds. Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call Us
Talk to a product expert
Call us now at:
021-42871228
Jakarta: 021-26538568 Extension 1290/1292
Bandung: 022-4215995
Surabaya: 031-5355111
Makassar: 0411-448381
Bali: 0361-499048, 0361-499035
Mon - Fri - 9:00 a.m 5:00 p.m
Sat: 9:00 a.m 1:00 p.m