How To
How To
1076 results
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure the E65BTNC headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Slide the power button in an upwards position. The power button will be located on the right arm next to the bluetooth button. Once you power on you will hear the audio chime. If this is your first time powering on the speaker, it will automatically go into pairing mode. You will see the fast blinking LED light as it searches for a device. Make sure that the device you are attempting to connect to is in pairing mode. The JBL Soundgear should be displayed on your discoverable devices within 3-8 seconds. Choose the JBL Soundgear and you are now connected!Was this helpful? Thank you for your feedback!
-
Make sure that the device you want to connect to is on and in pairing mode. Press and hold the center button on the inline microphone for 3-5 seconds. (We recommend putting one ear tip inside your ear to hear the audio prompt) You should here "powering on.....pairing" as it searches for your device. The Tune 205BT headphone should appear on your discoverable devices and should connect within 2-3 seconds. If you wish to pair to a different device, make sure the last device it was connected to has the bluetooth turned off. Make sure the headphones are off and press and hold the center button between 3-5 seconds or until the audio prompt states that it is "looking for device" You should be able to pair with a different device within 2-3 seconds.Was this helpful? Thank you for your feedback!
-
Press the power button on the Flip 3 SE once to power on the device. When you power on the Flip 3 SE for the first time, it will automatically go into Bluetooth Pairing mode and you should be able to find the Flip 3 SE in the list of available Bluetooth devices on your mobile phone/tablet. Press the Bluetooth button on the Flip 3 SE to enable pairing mode manuallyWas this helpful? Thank you for your feedback!
-
There are several easy ways to prevent damage to your headphones, and please follow the steps below.
-
If the USB port has a cover, please always have it covered, except when charging.
-
Always be sure the USB port and connector are dry before connecting to charge.
-
Do not allow any oils, stains, sweat, or corrosive materials to contact the charging port. It will eventually damage the port.
-
Do not damage or block the USB port. For example, do not force it in if you have trouble inserting the USB connector into the port. Instead, examine the port and remove foreign substances that might be inside or blocking the port.
Was this helpful? Thank you for your feedback! -
-
1. Press and hold the surround button on the Soundbar, until the system enter "learning mode"(the LED will blink orange). 2: VOLUME + : Press 'Volume +' on the soundbar and then press 'Volume +' on the TV remote control. 3: VOLUME ? : Press 'Volume �' on the soundbar and then press 'Volume �' on the TV remote control. 4: MUTE: Press 'Volume +' and 'Volume �' together on the soundbar and then press 'Mute' on the TV remote control. 5: POWER: Power On your soundbar by pressing the 'Power' key on the soundbar and then pressing the 'Power' key on the TV remote control. Note: After each TV IR code is programmed, the blinking orange LED will turn white for 1 second. The soundbar is ready to learn the next key after the white LED disappears and the orange LED begins to blink.Press and hold the top panel 'Surround' key again to exit learning mode (the orange LED will stop blinking).Was this helpful? Thank you for your feedback!
-
The owner's manual can be a bit difficult to understand. Here is what to do to program a preset station that has not already been saved in any preset: 1 Turn on the radio by clicking the FM button. 2 Find the station you want to save by doing what is shown under pt. 8 B or C, either clicking or pressing/holding for more than 2 seconds the left/right arrow buttons. 3 Press and hold the FM button for more than 2 seconds. Now the preset number appears blinking. 4 Click on the left/right arrow buttons to skip through the preset positions. 5 When you have located the desired memory preset position, such as Preset 4, confirm by clicking the FM button. Now the desired FM station is saved in memory preset 4. If you have already saved an FM station in a preset memory position, and want to have a new station placed there instead, here is what to do: 1 Turn on the radio by clicking the FM button. 2 Jump to the preset station you want to change with the round central button. Each click advances to the next preset. 3 When you are on the preset you want to change, e.g. preset 4, press and hold the FM button for more than 2 seconds. 4 The FM symbol and the frequency will now blink. 5 Before they stop blinking, click, or press and hold one of the arrow buttons to go through the FM frequencies step by step, or perform station search. 6 When you have found the new station you want to save in preset 4, click the round central button. 7 Now the new station is saved in preset 4.Was this helpful? Thank you for your feedback!
-
Instructions are located on a MapMyRun insert in the product box. There will be a 15 Character Access Code printed on the insert card, or you can visit www.mapmyrun.com/promo/UA. If you are not a MapMyRun Member you will need to register on the website before you can redeem your Access Code. If you are already a member with an Annual Premium Membership you cannot combine memberships. You will need to visit the link and use your code to renew for 1-Year when your current membership has expired. Refer to the expiration date on your Access Code to ensure that it does not expire. If you are a member with a monthly Premium Membership you can cancel your monthly premium and then visit the link to enter the 1-Year Access Code. If you experience any issues with the code or have additional questions, please reach out to the customer service team mvpbilling@underarmour.comWas this helpful? Thank you for your feedback!
-
Instructions are located on the back of the “Find Your Fit” insert in the product box. There will be a 15 Character Access Code printed on the insert card, or you can visit www.mapmyfitness.com/promo/UAWireless. If you are not a MMF Member you will need to register on the website before you can redeem your Access Code. If you are already a MMF Member with an Annual Premium Membership you can visit the link and use your code to renew for 1-Year when your membership is up for renewal. Refer to the expiration date on your Access Code to ensure that it does not expire. If you are a MMF Member with a monthly Premium Membership you can cancel your monthly premium and then visit the link to enter the 1-Year Access Code.Was this helpful? Thank you for your feedback!
-
Instructions are located on the back of the “Find Your Fit” insert in the product box on a red paper. There will be a 15 Character Access Code is printed on the insert card or you can visit www.mapmyrun.com/promo/UA. If you are not a MMR Member you will need to register on the website before you can redeem your Access Code. If you are already a MMR Member with an Annual Premium Membership you can visit the link and use your code to renew for 1-Year when your membership is up for renewal. Refer to the expiration date on your Access Code to ensure that it does not expire. If you are a MMR Member with a monthly Premium Membership you can cancel your monthly premium and then visit link to enter the 1-Year Access Code.Was this helpful? Thank you for your feedback!
-
Press and hold the multi-function button shown in “quick start guide” section 5 to ignore incoming call.Was this helpful? Thank you for your feedback!
-
(1) Select the JBL speaker/soundbar you want to rename
(2) Navigate to the Support tile and select "Rename My Product."
(3) Press the current name and type in the new name
(4) Press SAVEWas this helpful? Thank you for your feedback! -
With the headphone in OFF state, press and hold the ON/OFF button for about 7 seconds for the Everest, 16 seconds for the Everest ELITE models. (ELITE changes to 7 seconds as well from software 0.5.6). Bluetooth memory is now erased, and new pairings can be made. An ELITE headphone permits pairing with one source device at a time. If you do not want to do a complete reset as described above, you can use the following method. Without reset, ELITE will try to re-pair with the last source when switched ON. If the last source is not detected, maybe because you want to use another source device, switch the ELITE off and on again, and make sure that the last source device you used is no longer switched ON. This way the ELITE will not be able to "see" the old source, and it will search for a new one. Now the ELITE will again search for the last paired source, and since it cannot find it after some seconds, it will switch back to be open for pairing with a new source. The LED will blink red/blue as an indication of this. The Everest BT models permit pairing with two source devices simultaneously. If you have used both source pairings, and want to pair to a third source, please perform the reset as described above (hold the ON/OFF button for about 7 seconds with the Everest OFF). Now you can again pair two source devices.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.Was this helpful? Thank you for your feedback!
-
With the headphones switched ON, press and hold both volume buttons for more than 5 seconds.
Your headphones are now reset to factory status.
Was this helpful? Thank you for your feedback! -
In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.Was this helpful? Thank you for your feedback!
-
Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.Was this helpful? Thank you for your feedback!
-
For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.
Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.Was this helpful? Thank you for your feedback! -
- Turn the unit ON.
- Press and hold the VOLUME + and PLAY/PAUSE buttons at the same time for more than 5 seconds.
- Unit is now reset.
Was this helpful? Thank you for your feedback! -
Press Phone and "volume +" > 2 sec. Power must be on.Was this helpful? Thank you for your feedback!
-
We offer a 30 day free return period. To initiate a return request, go to "Return Products" under "Order Support" in the menu bar.
Was this helpful? Thank you for your feedback! -
The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.Was this helpful? Thank you for your feedback!
-
While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.Was this helpful? Thank you for your feedback!
-
Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.Was this helpful? Thank you for your feedback!
-
The JBL product is in a deep sleep mode, which it is to prolong the lifetime of the battery. Connect the case to a charger for about 2 seconds to wake the product up and take the earbuds out from the case. Once you put the earbuds back in the case, it's ready to pair through Bluetooth.
Was this helpful? Thank you for your feedback! -
The best way to remove the enhancer from the ear bud is to gently pull back the outer rim of the enhancer that is located around the base of the ear bud. When replacing the current enhancers with a different size, please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. The LEFT enhancer will feature the square cut out that allows you to receive your Heart Rate reading. It is important that the small digital square on the ear bud is fully exposed and the enhancer cut out is placed around it and not over it. If the enhancer is not attached properly, you will hear the audible voice stating that it cannot receive an accurate reading on your heart rate and you will need to readjust the enhancer.Was this helpful? Thank you for your feedback!
-
The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00