How To
How To
1097 results
-
Some vehicles don’t provide an isolated ground for the head unit which may introduce noise. Please connect your smartphone to JBL DRG and enable the “Aux Noise Cancel” button in the App. This can be found right after Aux Line option in Connection Mode section.Was this helpful? Thank you for your feedback!
-
Some head units in the vehicles use isolated grand, if JBL DRG use isolated grand as well, this will disable the chips inside DRG. Please connect your smartphone with JBL DRG and disable the “Aux Noise Cancel” button in the Apps right after Aux Line option in Connection Mode section.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Focus 700 is actually the Focus 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
What you are experiencing is normal. The Inspire 700 is actually the Inspire 500 headphone but with the added bonus of a charging case.Was this helpful? Thank you for your feedback!
-
Please press the round POWER Button on the FLIP again for 3 seconds, until the light in the button flashes blue/red. This will deactivate any active BT connection in the FLIP, and it should now become visible in the list of BT components on your smartphone or tablet. Pairing is now possible.Was this helpful? Thank you for your feedback!
-
JBL LINK 10 and LINK 20 has 32 volume steps, and LINK 300 and LINK 500 has 48 volume steps. For broader volume changes, hold down either the volume + or - butons. Use individual presses for fine volume adjustments.Was this helpful? Thank you for your feedback!
-
The volume level of the speaker is depends on the level of the source file itself. Some Dolby Atmos Music tracks are made to be quieter, and some louder.
Was this helpful? Thank you for your feedback! -
The answer depends on the method used for connecting the Partybox Ultimate units:
Multi-Room Music (Airplay/Alexa/Google Home) - No effects or audio samples heard on secondary speaker(s).
Stereo Mode (JBL One app) - Both effects and audio samples heard on secondary speaker.
Multi-Speaker Connection (pressing the relevant buttons on the top panels) - No effects heard, but audio samples heard on secondary speaker(s).
Daisy Chain (wired Aux connection) - Both effects and audio samples heard on secondary speaker(s).
Was this helpful? Thank you for your feedback! -
When a connected Bluetooth device goes out of range, the JBL Micro Wireless will try to reconnect to it for 3 minutes. After 3 minutes the Micro Wireless can connect to other Bluetooth devices again.Was this helpful? Thank you for your feedback!
-
Soundshift only works for the Boost TV itself, and cannot stop the other JBL Connect device. To stop the second device, press the JBL Connect button on your remote or device and they will disconnect.Was this helpful? Thank you for your feedback!
-
If you see this message, you must download the Device Utility app from the Google Play Store. Follow the instructions in the app to activate your speaker, and then return to the Google Home app to complete the setup.
Was this helpful? Thank you for your feedback! -
This is addressed in the owner's manual. After associating a group of four speakers, when deciding to go back to normal operation as two pairs, it is recommended to reset them to factory default settings, which requires associating speaker pairs again.Was this helpful? Thank you for your feedback!
-
JBL Connect feature is using Bluetooth technology, so it is hard to say how far you can walk away. Depending on what other signals you have at your place that could interupt and wall material between speakers.Was this helpful? Thank you for your feedback!
-
If the network does not appear, you can manually type in the network name (SSID) and password to connect.
Was this helpful? Thank you for your feedback! -
You can manually type in the network name (SSID) and password to connect if the network does not appear.Was this helpful? Thank you for your feedback!
-
When you have associated two pairs of speakers, the range between primary and secondary speakers (all 3 speakers), will be maximum 10 meters. The range will increase if you only use one pair of speakers (30 meters). We recommend placing the speakers on a high-level surface or shelf, for best possible connection.Was this helpful? Thank you for your feedback!
-
You should hear the audible voice stating ‘low battery’ when you have about 20 minutes left of battery life left on the UA WIRELESS headphones. If you have an Apple device, you will actually be able to see the battery life in the upper right hand corner of the device next to the BT symbol.Was this helpful? Thank you for your feedback!
-
If there is no activity on your JBL Boost TV, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.Was this helpful? Thank you for your feedback!
-
If there is no activity on your JBL SB 250, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.Was this helpful? Thank you for your feedback!
-
NOTE: LINK speakers must be set up on a WiFi network before Bluetooth can be activated. Once it is set up, you can use Bluetooth anywhere (Unless you reset the speaker and start all over with installation).
Pairing issues with a Smartphone or Tablet:- First try to restart the Bluetooth connection on your source device (Smartphone/tablet) by switching Bluetooth off and on again with a short pause in between.
- Forget previous paired connection (on your smartphone/tablet) in your Bluetooth settings if you once had paired with our product.
- Try to restart source device(Smartphone/tablet) by powering it off and on again, and after restart try to establish a Bluetooth connection to your JBL LINK device.
- If above does not work, then try to restart your JBL LINK device by turning it off and on again.
- Press and hold down the Bluetooth button on your JBL LINK device to initiate pairing mode again.
- Go into Bluetooth settings on your Smartphone/tablet.
- Perform a restart or reset if you are not able to connect after above steps.
JBL LINK Bluetooth specifications:- Bluetooth version 4.2
- A2DP v1.3 with SBC Audio Codec.
- AVRCP v1.5
Was this helpful? Thank you for your feedback! -
There are multiple ways to check your heart rate (HR) while using your headphones both in and out of workouts. On the UA Record mobile app select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your current heart rate will appear under the headphones' image. You will hear your heart rate when using the headphones during a UA Record workout with audio coaching. While using with your UA Band during a workout your HR will be shown with your workout stats and will coordinate with the HR zone LED on the Band. You also can simply tap the UA logo on the RIGHT ear bud to hear the audible voice stating your heart rate reading.Was this helpful? Thank you for your feedback!
-
Replacement parts are available from authorized dealers and Service Centers. Please contact our customer service department for more information and contact details.Was this helpful? Thank you for your feedback!
-
At the bottom of your Horizon alarm clock, you will see a little cap where the backup-battery resides. Turn the cover lid left to open it, and on the back of the cover lid, you will see the serial number.Was this helpful? Thank you for your feedback!
-
You can view stats from your past workouts by going to your dashboard and tapping the Fitness quadrant. Tap the workout you would like to view. Your average and peak heart rate, heart rate distribution through your training session, and a graph of your real-time heart rate, will all be shown.Was this helpful? Thank you for your feedback!
-
For headphones with version 4.0 of the firmware, updates will be available via jbl.com/app. For headphones with firmware version 5.0 or higher, update notification will be pushed via the appWas this helpful? Thank you for your feedback!
-
You can set the time limit in JBL Safe Sound/Daily Time Limit.
Was this helpful? Thank you for your feedback! -
The sensor is located in the LEFT ear bud. The left enhancer will feature a cut out for the sensor and should be fully exposed.Was this helpful? Thank you for your feedback!
-
The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.Was this helpful? Thank you for your feedback!
-
Under the little hole next to the phone reciever button.Was this helpful? Thank you for your feedback!
-
On the BT and ELITE NXT series over-ear and on-ear models, the serial number sticker is on the inside of the headband left side, visible when the size adjustment is pulled all the way out. Serial numbers are also shown on the boxes. On ELITE 100 in-ear, it is on the box only.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00