How To
How To
1102 results
-
To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the UA WIRELESS headphone. Once you select that option, the audible voice should state, “connected”.Was this helpful? Thank you for your feedback!
-
It is not possible to turn the Google Assistant feature off on the headphones, but if you turn off GA on your phone, the headphones won't trigger. On the Everest GA models, the Google Assistant feature is in fact than an extension of your phone, so once you connect to your phone via BT, when you touch the right ear pod, it commands your phone to open the "Hey Google" command.
The only way to stop that from happening is to change the Google settings on your phone to deactivate Google Voice Match, or deactivate Google Assistant entirely.
Was this helpful? Thank you for your feedback! -
Press and hold the center button for 3-5 seconds until the audible voice states “power off” you will briefly see a red light before it completely powers down.Was this helpful? Thank you for your feedback!
-
Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.Was this helpful? Thank you for your feedback!
-
Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.Was this helpful? Thank you for your feedback!
-
The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.Was this helpful? Thank you for your feedback!
-
The best way to remove the enhancer from the ear bud is to gently pull back the outer rim of the enhancer that is located around the base of the ear bud. When replacing the current enhancers with a different size, please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. The LEFT enhancer will feature the square cut out that allows you to receive your Heart Rate reading. It is important that the small digital square on the ear bud is fully exposed and the enhancer cut out is placed around it and not over it. If the enhancer is not attached properly, you will hear the audible voice stating that it cannot receive an accurate reading on your heart rate and you will need to readjust the enhancer.Was this helpful? Thank you for your feedback!
-
The JBL product is in a deep sleep mode, which it is to prolong the lifetime of the battery. Connect the case to a charger for about 2 seconds to wake the product up and take the earbuds out from the case. Once you put the earbuds back in the case, it's ready to pair through Bluetooth.
Was this helpful? Thank you for your feedback! -
Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.Was this helpful? Thank you for your feedback!
-
The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
-
To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00