How To

Support Overview / How To

How To

1096 results

Sort

Page size

How do I use the unit as a microphone/speaker?

Make sure your device is paired with a mobile device. When receiving a call, press the phone button to answer the call. You can now use it as a speakerphone.

Was this helpful? Thank you for your feedback!
How do I use the ShareMe option on my Headphones?

The ShareMe button is marked with an S in a circle, and must be clicked briefly. Do not keep the button pressed. Step 4 may go wrong if not done correctly. Please make sure that you have the second Everest 300 turned off. Now press AND HOLD the on/off button for about 15 seconds. The LED must switch to white/red blinking to indicate that it is actually in BT pairing mode. Now simply wait until the two headphones have communicated with each other, and established the BT connection. The white led below the S buttons will light constantly on both headphones when the ShareMe connection is ready. Now you just begin music play on the source, and both headphones will play.

Was this helpful? Thank you for your feedback!
How do I use the Google Assistant with my headphones?

- For more information on what your Google Assistant can do, visit: assistant.google.com/platforms/headphones

Was this helpful? Thank you for your feedback!
How do I use my UA Headphones with Record?

Connect your headphones and start a workout using UA Record's heart rate zone tracking. Track your current heart rate zone so you know when to rest or power up, while also viewing your total heart rate distribution throughout each training session. Know your current, average, and peak heart rate. You also have the option to hear your stats read aloud during a workout. With UA Record, you can customize what feedback you hear by setting your stats, frequency, voice, and volume.

Was this helpful? Thank you for your feedback!
How do I use Amazon Alexa with my headphones?

- Single tap the left ear cup to engage Alexa.

For more information and things to try with Alexa, visit: www.amazon.com/alexadevices and select ‘Use Alexa’.

Was this helpful? Thank you for your feedback!
How do I turn SoundShift On?

1. First pair your phone to the Boost TV. You can test this by streaming music to the product. 2. Then press the TV button to switch to the TV sound. Press the TV button again so the LED light is blue--Blue LED means that SoundShift is ON. 3. When you press PLAY on your phone, then you will hear your Bluetooth audio break in over the TV sound. This confirms that SoundShift is working. 4. Simply press SoundShift button again, this will now turn OFF the SoundShift. Now you can watch TV without any interruption from Bluetooth devices.

Was this helpful? Thank you for your feedback!
How do I turn on pairing mode?
To activate Bluetooth pairing mode, please follow these steps:
- Press the Bluetooth button on the bottom of the right headphone.
Now find the Headphone in your Bluetooth device settings and select it to connect.
Was this helpful? Thank you for your feedback!
How do I turn on and pair the UA headphones with my device?

To power on the device, place one of the headphones inside your ear and press and hold the center button on the inline mic. You should hear the audible voice stating, “powering on” and a blue blinking light should appear at the top of the inline mic. If this is your first time connecting to a device, it should immediately go into pairing mode. The device should recognize the UA WIRELESS headphone. Once you select that option, the audible voice should state, “connected”.

Was this helpful? Thank you for your feedback!
How do I turn off the Google Assistant on the JBL Everest 310GA and 710GA?

It is not possible to turn the Google Assistant feature off on the headphones, but if you turn off GA on your phone, the headphones won't trigger. On the Everest GA models, the Google Assistant feature is in fact than an extension of your phone, so once you connect to your phone via BT, when you touch the right ear pod, it commands your phone to open the "Hey Google" command.
The only way to stop that from happening is to change the Google settings on your phone to deactivate Google Voice Match, or deactivate Google Assistant entirely.

Was this helpful? Thank you for your feedback!
How do I turn off the device?

Press and hold the center button for 3-5 seconds until the audible voice states “power off” you will briefly see a red light before it completely powers down.

Was this helpful? Thank you for your feedback!
How do I turn off my internal TV speakers?

Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.

Was this helpful? Thank you for your feedback!
How do I turn off my internal TV speakers?

Every TV is different, but most current TVs will let you turn off your internal TV speakers in the Settings menu under the Audio section.

Was this helpful? Thank you for your feedback!
How do I turn off my E45BT or E55BT?

The on/off button is a spring-loaded slider button. Press the button upwards against the spring pressure, and hold it there for about three seconds. Now you will hear the "off" prompt sound in the headphone speakers, and the LED light goes out. Now the headphones are switched off. Please note that if you do not play music or press any button for about 10 minutes, the headphones will switch off automatically.

Was this helpful? Thank you for your feedback!
How do I switch the enhancer sizes?

The best way to remove the enhancer from the ear bud is to gently pull back the outer rim of the enhancer that is located around the base of the ear bud. When replacing the current enhancers with a different size, please make sure to align the funnel of the enhancer tip over the small speaker screen of the headphone casing. The LEFT enhancer will feature the square cut out that allows you to receive your Heart Rate reading. It is important that the small digital square on the ear bud is fully exposed and the enhancer cut out is placed around it and not over it. If the enhancer is not attached properly, you will hear the audible voice stating that it cannot receive an accurate reading on your heart rate and you will need to readjust the enhancer.

Was this helpful? Thank you for your feedback!
How do I start the product for the first time?

The JBL product is in a deep sleep mode, which it is to prolong the lifetime of the battery. Connect the case to a charger for about 2 seconds to wake the product up and take the earbuds out from the case. Once you put the earbuds back in the case, it's ready to pair through Bluetooth.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the T205?

Two quick clicks on the microphone will skip the track forward. Three quick clicks on the microphone will skip the track backward to the previous song.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Synchros E30?

The track control button is located in the center of the inline microphone. This also serves as the pause/play button and enables you to answer and hang up phone calls. Two quick clicks on the center button will skip the tracks forward to the next song. Multiple quick clicks will skip the tracks backward. Compatibility may vary with some older phone models.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Everest 750NC?

To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do I skip tracks on the Everest 310/710 headphones?

To skip the tracks forward, you press and hold the volume up button for 3 seconds. To skip tracks backward, press and hold the volume down button for 3 seconds.

Was this helpful? Thank you for your feedback!
How do I see when my JBL E45BT or E55BT is fully charged?

While charging, the charging indicator diode is lighting constantly. When charging is complete, the light goes out.

Was this helpful? Thank you for your feedback!
How do I see that battery is low?

The charging LED on the headset will flash red when the battery is low. For the ELITE models, a more accurate indication of remaining battery time can be seen on the fuel gauge in the app.

Was this helpful? Thank you for your feedback!
How do I return an order?

We offer a 30 day free return period. To initiate a return request, go to "Return Products" under "Order Support" in the menu bar.

Was this helpful? Thank you for your feedback!
How do I reset to factory defaults?

Press Phone and "volume +" > 2 sec. Power must be on.

Was this helpful? Thank you for your feedback!
How do I reset this unit back to factory settings?
1. Turn the unit ON.
2. Press and hold the VOLUME + and PLAY/PAUSE buttons at the same time for more than 5 seconds.
3. Unit is now reset.
Was this helpful? Thank you for your feedback!
How do I reset the Endurance Series Headphones?

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

Was this helpful? Thank you for your feedback!
How do I reset the device to factory settings?

Power ON the device, then press and hold the "Volume+" and the "Play/Pause" buttons at the same time. When the device switches off after a few seconds, sounding the OFF prompt, it has been reset.

Was this helpful? Thank you for your feedback!
How do I reset the Charge 4?

In order to reset the Charge 4, with the unit on, press “Volume+” and “Bluetooth” at the same time for 3-4 seconds until you hear the audible chime.

Was this helpful? Thank you for your feedback!
How do I reset my JBL headphones?

With the headphones switched ON, press and hold both volume buttons for more than 5 seconds.
Your headphones are now reset to factory status.

Was this helpful? Thank you for your feedback!
How do I reset my JBL Everest 310, 710 and 750 Elite headphones?

With the headphones switched ON, press VOLUME + and VOLUME - , and hold them for 5 seconds. Your headphones are now reset to factory settings. This is true for Everest 310, 710, Elite 750, 310GA and 710GA.

Was this helpful? Thank you for your feedback!
How do I reset my Everest or Everest Elite headphone to pair with another Bluetooth source?

With the headphone in OFF state, press and hold the ON/OFF button for about 7 seconds for the Everest, 16 seconds for the Everest ELITE models. (ELITE changes to 7 seconds as well from software 0.5.6). Bluetooth memory is now erased, and new pairings can be made. An ELITE headphone permits pairing with one source device at a time. If you do not want to do a complete reset as described above, you can use the following method. Without reset, ELITE will try to re-pair with the last source when switched ON. If the last source is not detected, maybe because you want to use another source device, switch the ELITE off and on again, and make sure that the last source device you used is no longer switched ON. This way the ELITE will not be able to "see" the old source, and it will search for a new one. Now the ELITE will again search for the last paired source, and since it cannot find it after some seconds, it will switch back to be open for pairing with a new source. The LED will blink red/blue as an indication of this. The Everest BT models permit pairing with two source devices simultaneously. If you have used both source pairings, and want to pair to a third source, please perform the reset as described above (hold the ON/OFF button for about 7 seconds with the Everest OFF). Now you can again pair two source devices.

Was this helpful? Thank you for your feedback!