How To
How To
1102 results
-
Under the little hole next to the phone reciever button.Was this helpful? Thank you for your feedback!
-
The heart rate sensor is located inside the RIGHT earbud inside the sound tunnel. If the Heart Rate detection is activated and you remove the RIGHT earbud, the audio voice will notify you to insert the ear bud and will recalibrate once it is detected again.Was this helpful? Thank you for your feedback!
-
The sensor is located in the LEFT ear bud. The left enhancer will feature a cut out for the sensor and should be fully exposed.Was this helpful? Thank you for your feedback!
-
You can set the time limit in JBL Safe Sound/Daily Time Limit.
Was this helpful? Thank you for your feedback! -
For headphones with version 4.0 of the firmware, updates will be available via jbl.com/app. For headphones with firmware version 5.0 or higher, update notification will be pushed via the appWas this helpful? Thank you for your feedback!
-
You can view stats from your past workouts by going to your dashboard and tapping the Fitness quadrant. Tap the workout you would like to view. Your average and peak heart rate, heart rate distribution through your training session, and a graph of your real-time heart rate, will all be shown.Was this helpful? Thank you for your feedback!
-
At the bottom of your Horizon alarm clock, you will see a little cap where the backup-battery resides. Turn the cover lid left to open it, and on the back of the cover lid, you will see the serial number.Was this helpful? Thank you for your feedback!
-
Replacement parts are available from authorized dealers and Service Centers. Please contact our customer service department for more information and contact details.Was this helpful? Thank you for your feedback!
-
There are multiple ways to check your heart rate (HR) while using your headphones both in and out of workouts. On the UA Record mobile app select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your current heart rate will appear under the headphones' image. You will hear your heart rate when using the headphones during a UA Record workout with audio coaching. While using with your UA Band during a workout your HR will be shown with your workout stats and will coordinate with the HR zone LED on the Band. You also can simply tap the UA logo on the RIGHT ear bud to hear the audible voice stating your heart rate reading.Was this helpful? Thank you for your feedback!
-
NOTE: LINK speakers must be set up on a WiFi network before Bluetooth can be activated. Once it is set up, you can use Bluetooth anywhere (Unless you reset the speaker and start all over with installation).
Pairing issues with a Smartphone or Tablet:- First try to restart the Bluetooth connection on your source device (Smartphone/tablet) by switching Bluetooth off and on again with a short pause in between.
- Forget previous paired connection (on your smartphone/tablet) in your Bluetooth settings if you once had paired with our product.
- Try to restart source device(Smartphone/tablet) by powering it off and on again, and after restart try to establish a Bluetooth connection to your JBL LINK device.
- If above does not work, then try to restart your JBL LINK device by turning it off and on again.
- Press and hold down the Bluetooth button on your JBL LINK device to initiate pairing mode again.
- Go into Bluetooth settings on your Smartphone/tablet.
- Perform a restart or reset if you are not able to connect after above steps.
JBL LINK Bluetooth specifications:- Bluetooth version 4.2
- A2DP v1.3 with SBC Audio Codec.
- AVRCP v1.5
Was this helpful? Thank you for your feedback! -
If there is no activity on your JBL SB 250, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.Was this helpful? Thank you for your feedback!
-
If there is no activity on your JBL Boost TV, it will go into standby mode after 20 minutes, and will take a couple of seconds to turn on after standby mode.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 08.00-17.00
Saturday - Sunday: 09:00-15:00
WhatsApp Us
Send us a message on +44 161 222 3325 or click here
Monday - Friday: 08.00-17.00Saturday - Sunday: 09:00-15:00