JBL Endurance PEAK

FAQs & How-Tos

13 results

Sort

Page size

aptX Audio Codec Support

This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.

Was this helpful? Thank you for your feedback!
Cleaning Instructions for Re-establishing Charging

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all True Wireless Stereo earphones and cases.

Was this helpful? Thank you for your feedback!
Endurance Series Headphones: Apt X

The Endurance headphones do not support Apt X or AAC audio codecs.

Was this helpful? Thank you for your feedback!
Endurance Series Headphones: Charging

Fully charge the earbuds along with the charging case before the first use. The charging case is for charging the earbuds only. LED behaviors: 1 LED- 25% 2 LED-25%-50% 3 LED-50%-75% 4 LED-75%-99% NO LED-100% Fully Charged You can keep the earbuds in standby mode for up to 3 hours without having to return them to the case. beyond this point the earbuds must be returned to the case for charging. You should receive up to 4 hours of playback with additional 24 hours of backup power from the charging case.

Was this helpful? Thank you for your feedback!
Endurance Series Headphones: Pairing Information

If connecting for the first time, the headphone will enter pairing mode automatically after it is powered on. To turn the headphones on, simply spread apart the RIGHT power hook from the cord. You will see solid red LED and then it will flash blue as it begins to search for a device to connect to. The Endurance headphone should pop up on your discoverable devices within a few seconds and you should be connected! If you wish to turn off the headphones, remove them from your ear and allow the RIGHT power hook and cord to close together. This is magnetized, so they should close together with ease.

Was this helpful? Thank you for your feedback!
Endurance Series Headphones: Switching Devices

To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.

Was this helpful? Thank you for your feedback!
Endurance Series Headphones: Track Control

To pause/play press the "L" on the JBL logo located on the RIGHT ear for 1 second. If you want to skip the track forward, press the "L" on the JBL logo on the RIGHT ear hook for 2 seconds. To skip tracks backward, press the "L" on the JBL logo on the RIGHT ear hook for 3-4 seconds.

Was this helpful? Thank you for your feedback!
Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using.

Was this helpful? Thank you for your feedback!
How do I prevent damage to my USB charging sockets for my headphones?
There are several easy ways to prevent damage to your headphones, and please follow the steps below.
1. If the USB port has a cover, please always have it covered, except when charging.
2. Always be sure the USB port and connector are dry before connecting to charge.
3. Do not allow any oils, stains, sweat, or corrosive materials to contact the charging port. It will eventually damage the port.
4. Do not damage or block the USB port. For example, do not force it in if you have trouble inserting the USB connector into the port. Instead, examine the port and remove foreign substances that might be inside or blocking the port.
If you need more assistance, please contact the Customer Service team.
Was this helpful? Thank you for your feedback!
How do I reset the Endurance Series Headphones?

For all models except Endurance Peak:
Press the headphone touch control located on the RIGHT ear loop for 15 seconds while the headphones are being charged.
Note that resetting the Dive will not erase music contained in the MP3 memory.

Endurance Peak reset: While the pods are being charged, tap the touch pad on the right pod once, then tap again and hold for approx 18 seconds, or until the LED blinks.

Was this helpful? Thank you for your feedback!