How To

There will be times that the LEFT ear will disconnect from the RIGHT or (primary) earbud. To get the Left ear to reconnect, make sure that the RIGHT earbud is on and emitting sound. Take the LEFT ear out of the charging case and put in ear. Press and hold down the power button on the LEFT ear bud for 5-8 seconds. You should hear the power on chime and then both ear buds should emit sound now. 

No, since the speaker does not store any information locally. To remove all settings from your stolen device, simply unlink the speaker from your account, and the next time the speaker goes online it will not connect to your account. However, if you have used the command ""Remember this"" feature, please beware of sensitive information, as the speaker will inform you of whatever you have asked it to remember. But after unlinking the speaker, it will forget.

Try to move the microphone closer to the sound source and adjust it for a better angle. You should also try to decrease the microphone volume to an appropriate level by turning the volume down.

Finally, try to enable the Dynamic Range Compressor (DRC) option in the QuantumEngine to lower the chance of distortion.

Try to move the microphone closer to the sound source and adjust it for a better angle. You should also try to increase the microphone volume to an appropriate level by turning the volume up.
Finally, try to increase or decrease the microphone gain level if the sound is distorted.

If your parcel is showing signs of damage upon delivery, we recommend that you refuse to accept it.

The parcel will then be returned to our warehouse, and you will automatically receive a refund.

If you already accepted your parcel, please take pictures of the damage(s) before opening the parcel.

We hope that the product(s) you have ordered are without any damage.

If the product(s) are damaged, please contact Customer Support as soon as possible, and no later than 2 days after receival of the parcel as we have a short window to process claims with our delivery partner.

Please note that you must keep all packaging, including the brown shipping box, while our Customer Support team is opening a claim with our delivery partner.

We use a sophisticated vetting process to ensure that your image does not contain copyrighted, protected, sexual, suggestive, offensive or inappropriate elements. This includes words and messages. If these algorithms are triggered, your order is automatically cancelled. Please try again with a different image or wording.

1. Ensure that your JBL One app device is less than 10m/33ft from the speaker during the initial set-up.
2. Ensure it is plugged into power and the power LED is illuminated.
3. Unplug the power cord, wait 10 seconds, reconnect the power cord and allow the speaker to power up.
4. Temporarily relocate either the speaker or router so that they are closer together.  If the connection succeeds, the original location may be too far from the router to maintain a stable connection.
5. Try using a different device with the JBL ONE app installed and connected to your home network.

It is usually not necessary to replace an unresponsive remote control. First, check to see if there is a small plastic tab extending out of the base of the remote control. This is a protective sleeve installed on new remote controls to prevent the battery from draining. Pull this tab to remove the plastic sleeve. The sleeve must be removed before the remote will operate. If the sleeve was removed or not present and the remote control is not working then a new battery should be installed before replacing the remote control. There is a small slide out drawer that houses the battery. The battery type will be either CR2025 or CR2032 for remotes of this size. Replacement batteries are commonly available from most electronic and convenience stores that sell small batteries. Check the number on the original battery and replace it with a battery that uses the same number. These steps will typically solve the problem.

This can be caused by dirt and dust accumulating on the charging arm, which can reduce the effectiveness of the adhesive. Clean the surface of the charging arm with a wet cloth or alcohol wipes. Do not use paper towels as these can leave paper debris.

There are two ways to blow speakers. The first is the one we all know and understand. If you pump 500 watts into a speaker that is only rated at 100 watts, kaboom, it blows up. As a result, very few of us do this. So then why are all of these poor, helpless speakers blowing up? Because of the second reason, under-powering. It's really a misleading term, but let's try to explain. First let's take it to the maximum. Example: You have a 1000 watt speaker and a 100 watt amplifier. The way you like to listen to music requires 300 watts. Typically, you will ask your amp to put out that 300 watts that you want to hear. The amp will do it, but it will clip and distort. Unfortunately, the human ear can't hear distortion until it reaches almost 10%. By that time it's usually too late. The speaker keeps trying to reproduce this distortion that it's not capable or reproducing and eventually it blows (usually the tweeter fails first). If you are blowing speakers with an amp that has a power rating lower than your speakers, you are pushing your amp too far, causing it to clip, and blowing speakers. If you are pushing your system too hard, it is suggested that you realize your systems limitations or recommend that you get a more powerful amplifier. Please realize, if you only buy speakers that will handle more power and not a more powerful amplifier, you won't solve the problem. The speakers will still blow, because it is distortion that is blowing them, not too much power.

Our Control X Wireless speaker has two different patterns for switching on, when using either battery or AC power. When using battery, turning on one speaker in either stereo mode or association mode (4 speakers connected), all will turn on simultaneously, no matter which is primary or secondary. When connected to AC power, switch on the primary speaker in stereo or associated mode, and the secondary speakers will follow. If you have associated speakers stereo or 4 speakers connected, then you have to press primary speaker's power button for more than 2 seconds, then the primary will send signal to secondaries, and they will wake up. It takes approx. 30-60 seconds before all are switched on. If your press it too short (less than 2 seconds), the primary speaker will not "pair" the secondary speakers together. Switch off the primary and start over again.

If your tracking has no updates for more than 3 days, please contact Customer Support for further assistance.

Please note that larger products, such as most party boxes, soundbars, and subwoofers will be delivered via a lorry on a pallet with our delivery partner for large shipments, DB Schenker. If so, you will receive an email from DB Schenker from which you need to schedule a delivery appointment. For more information about shipments via lorry on a pallet, see here: https://support.harmanaudio.com/gb/en/customer-service/large-shipments.html

If you have not received your parcel even though your tracking is stating that it was delivered, please contact Customer Support as soon as possible, for us to locate your parcel.

Please note that if you, at your own risk, have granted our delivery partner permission to deliver the parcel when you are not at home, we are unfortunately unable to open a claim with our delivery partner.

This is most likely due to CEC function. Some our soundbars supports CEC commands from your TV, and if some CEC commands will make the speaker react in a way you do not like, we suggest you disable all CEC functions from your TV. Please note, that your Soundbar will not turn on when your TV is turned on, due to disabling the CEC function.

When you are installing new apps or adding content to your LINK BAR, the system may be a bit slower when dealing with multiple things.
Here is a couple of things you should know.

1. You need a speedy internet connection to download all the content you added.
2. Wait for everything to be finished, then you can enjoy the system without any issues.
3. Reboot LINK BAR after installing all apps. A fresh reboot can help and enhance performance.

If you find yourself encountering audio dropouts or interference coming from your surround speakers when they are not docked on the main unit, here are a couple of tips to try to remedy that.

1. Try moving any wireless routers that are near the sound bar further away.

2. Reboot router so it can auto select a new frequency channel, since the sound bar and router may be on the same channel resulting in audible interferences

3. Re-position the surround speakers so they are closer to the main unit.

4. Re-calibrate the surround speakers

5. Adjust the volume on the sound bar and gradually raise the volume, if driven to hard the sound bar speakers can distort

Yes, rinse it under a faucet or under the shower, but not under full water pressure.

If you are having difficulty with the noise cancelling feature while on your PS4, please check your side tone setting in QuantumENGINE by connecting your Q800 to your PC. Please note that ANC will not work properly if the mic is on and sidetone is greater than 0. We recommend either muting the mic or change the sidetone in the JBL QuantumENGINE to 0. 

We've intentionally designed the flip-up boom mic to stay affixed to the headset. We know from experience that losing or breaking the detachable mic is never fun. Therefore, we designed the mic to fold neatly into the headset - this design also allows the mic to automatically mute when elevated. If you're wanting a detachable mic, please check out the Quantum 100 or the Quantum ONE.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. If you're using the USB dongle, check that the correct playback device is selected under Control Panel > Sound > Playback. Select the proper playback device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Ensure that the correct device is selected as the default device under Control Panel>Sound>Playback. Make sure the on headset volume control is turned up. Rotate the volume wheel on your headset to increase the volume. Check that the correct playback device is selected under Control Panel > Sound > Playback. Select the correct device, right-click, and select "Set as Default Device". Check the computer volume levels and make sure it is not muted or turned all the way down.

Make sure the volume control on the headset is turned up. Rotate the volume wheel on your headset to increase the volume. If you're connected to the PC via USB, check that the default device is selected under Control Panel > Sound > Playback. Select JBL Quantum 600 or Quantum 800 Game, right-click, and select "Set as Default Device". Check your headset's game-chat balance dial and ensure that the balance is correct. Check the JBL Quantum 600 or Quantum 800 Game device and make sure it is not muted or turned all the way down.

The JBL Xtreme will no longer appear in the JBL Portable app while using Apple devices with iOS 14 or later installed, due to incompatibility. 
You can continue to use the speaker as normal with these devices through Bluetooth or Aux connection, but it will no longer appear in the app. 
There are currently no plans to release a new Firmware as the JBL Xtreme has been discontinued. 

Let's see what we can try to do to solve your problem.

1. Check if the Privicy-Switch button is OFF (the MUTE button on the LINK BAR).
2. Go to the settings menu, “Device preference --> Google,” check “OK Google” detection is enabled.
3. Make sure there is no objects place on top of the LINK BAR which may block the microphones.

Every person has different preferences for wall mounting products. Nevertheless, we tried out varies options and found this to be the place for optimal sound performance.

1. Use the included "Wall-mount guide" that came with your LINK BAR.
2. From the down edge of your TV screen, measure 50mm (using the guide for the screws) or 5 cm or 2 inches depending on the country.
3. It will perfectly align the LINK BAR close to your TV and give the best performance.

Also, you won't have to deal with HDMI cables being too short!

These are our recommendation if you want to place it further down, be our guest!
The sound and performance will still be magnificent!

To power on and pair the headphones, remove the ear tips from the charging case. If this is your first time using the headphones, they will automatically go into pairing mode. You will see the blue and red LED light flash on the RIGHT and LEFT ear as it attempts to pair with your device. Make sure your device is in range and BT settings are ON. The JBL True Wireless Flash X should pop up on your list of discoverable devices within 3-5 seconds, tap and connect. Once connected, you will see a slow blinking blue light below the UA logo on the RIGHT and LEFT Ear. This headphone allows you to use the ear tips in Stereo or Mono mode. If you wish to just use the LEFT or RIGHT ear, simply place the ear tip you do not wish to use back in the charging case.

Try a manual pairing of the headset and the dongle.
Hold the power button in the "On" position for 5 seconds on the headset, and then hold the button on the dongle for 5 seconds. This should force a manual pairing, allowing the PC to again recognize the headset.
Be sure to check multiple USB ports (to confirm it’s not an issue with the USB port).
If the dongle can’t be manually paired either, please contact customer support.
 

In most cases when a Computer/PC/Laptop has issues connecting to a Bluetooth device (Portable speaker, Headphones, Active speakers), it's caused by your Computer/PC/Laptop's Bluetooth driver (software).

The driver (software) should support the following Bluetooth protocols, to be able to play music/sound from your Computer/PC/Laptop:

• A2DP (Advanced Audio Distribution Profile) driver for your Computer/PC/Headphones to transfer music.

• AVRCP (Audio/Video Remote Control Profile) driver to send skip/forward/pause/play music to your device

Always get the latest driver version available for your Computer/PC/Laptop.

To download the correct driver (software), visit the manufacturer's website of your Computer/PC/Laptop. They usually have a "Support/Download" section where you can find the correct driver. Otherwise, we advise you to contact their support.

First time you perform the pairing, it can take several minutes to establish connection. If more than five minutes go by with no result, please switch both units OFF and ON again.

If the two buds lose connection to each other, you can choose to force-pair the main/right bud to the secondary/left bud or the other way around.
For both buds, triple-click the button on one ear bud to pair with the other ear bud.

If you create a Stereo Pair using the JBL Portable App and you come within range of additional PartyBoost compatible speakers while they are ON, the app will find these speakers. This will break the stereo pair and create a mono PartyBoost group that includes all active speakers that are in proximity. This only happens when the JBL Portable App is actively running on the source device, including when it is running in the background, and when these other speakers are ON. To avoid this scenario, make sure the app is completely closed, without running in the background before coming near any additional PartyBoost speakers that happen to be ON.

NOTE: The Portable App does not need to be running in order to enjoy Stereo sound from two speakers

The new PartyBoost does not support the previous Connect and Connect+ features. For example: You will not be able to successfully connect the new PartyBoost enabled Flip 5 with a Connect+ enabled speaker like the Pulse 3 or Flip 4. You will not be able to connect the Boombox 2 to the original Boombox speaker.

If you are experiencing sound fading in and out (pumping) or volume levels changing while playing your instrument, this is known as limiting. The sound being sent into the PARTYBOX may be too loud which will cause the limiter in the speaker to kick in. This can cause the volume levels to dip. This is done to protect the speaker from playing louder than it’s rated output, and it likely means that the instrument input level on the PARTYBOX is set too high. Please perform these steps to calibrate your input level and to prevent pumping:

 

1.  While music is playing via BT or line input, set the volume on the PARTYBOX to a comfortable listening level.
2. Stop playing the music.
3. Turn the instrument/guitar input volume on the PARTYBOX all the way down.
4. Connect the instrument to the instrument/guitar input on the PARTYBOX.
5. Set the volume on your instrument to max.
6. Start playing the instrument and begin turning the instrument/guitar volume on the PARTYBOX up. The instrument should sound perfectly normal without any pumping or swelling. Continue to turn up the volume until you start to notice pumping or swelling. When you hear this, turn the volume back down a little bit until the pumping completely stops. You have now calibrated the input level for that instrument. During this step, as you are turning up, if it gets too loud, turn down the main volume on the PARTYBOX to a comfortable level, and then continue.

You should now use the main volume on the PARTYBOX to set the loudest volume for your instrument and can use the volume control on your instrument to adjust the level up or down.

 

NOTE: Whenever connecting a different instrument, you will likely have to repeat this process as all instruments (guitar pickups) have slightly different output levels. This is how you can ensure maximum performance out of your PARTYBOX.

Click here for a list of How To videos about the PartyBox 1000!

PARTYBOX 110
Software Update Release Notes
------------------------------------------------------------------------
Version:  1.35.0
Release Date:  September 19, 2022
Release Media:  OTA (over the air) Automatic Upgrade

What's New

What’s New:
The new Software version will enable Party mode across PartyBox 310 & PartyBox 110 series. 
Stereo mode will still only work when 2 PartyBoxes of the same model are connected. 

It is possible to pair two of the same model of JBL PartyBox speakers together through TWS (True Wireless Stereo) mode.

PartyBox On-The-Go*/On-The-Go Essential*/100:
Connect just the left PartyBox with the chosen device first, with the right PartyBox turned off. The speaker that is connected first will automatically be the left channel. Now turn the right PartyBox on and continue with TWS pairing (detailed below).

*The PartyBox On-The-Go and PartyBox On-The-Go Essential are compatible with each other in TWS mode.

PartyBox 200/300/1000:
A button (L/R) on the rear of the speakers is used to assign the correct channel to the speakers after pairing is made.
In order to activate TWS mode, press and hold the Bluetooth button on the first speaker until the notification chime sounds, about 5 seconds. Then press and hold the Bluetooth button on the second speaker until the notification chime sounds (as seen below). TWS mode is now activated. To disable TWS, press and hold the Bluetooth button on either speaker, or power off one speaker.

Partybox 110/310/710/Encore/Essential:
Press the buttons labelled TWS on both speakers to connect the speakers in TWS mode (pictured in item 2 in the image below, with two speakers on the button).

TWS can be activated and deactivated remotely in the JBL Partybox app, in addition to assigning the left and right channels to the correct speakers.
Once the TWS connection is setup, it will be in Stereo mode by default if both speakers are the same model, otherwise the speakers will be in Party mode by default if different Partybox models are used. You can also switch between Stereo and Party mode in the JBL PartyBox app if two of the same Partybox models are used.

Please note: In order to achieve TWS mode, the speaker must be the same model with the exception of the PartyBox 200 & PartyBox 300, and PartyBox On-The-Go & PartyBox On-The-Go Essential which can be paired together via TWS. You cannot achieve TWS with a PartyBox 1000 and a PartyBox 300. You cannot achieve TWS with a PartyBox 100 and PartyBox 200. However, it is possible to connect a maximum of two of either the JBL PartyBox app compatible models (PartyBox 110, 120, 310, 320, 710, Encore or Encore Essential) together in Party mode - the two speakers then do not need to be the same model, but Stereo mode will not be possible.

To charge the PartyLight Stick you need a charger with at least 5V/2A output. You can use the PartyLight Stick while it's charging.

The playtime for the PartyLight Stick is up to 8 hours. The playtime can vary depending on light, brightness, music, and environmental conditions. The playtime will also decrease if the backlight is turned on as this consumes more energy.

You can always check the battery level by pressing the power button twice. The white light on the PartyLight Stick will indicate the battery level. A red light indicates the battery level is low.

The JBL Quantum 350 Wireless headset is compatible via 2.4GHz wireless connection with:

• PC
• PlayStation
• Mac
• Nintendo Switch.

The JBL Quantum 100 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.

The JBL Quantum 200 is compatible with PC, PlayStation, Xbox, Nintendo Switch, Mobile, Mac and VR.

This product supports up to 10 hours of audio playtime. Please note that battery life may vary depending on volume level and content. 

The compatibility for JBL Quantum models on PlayStation 5 is the same as it is for PlayStation 4 models.
 All JBL Quantum headset models work through 3.5mm audio jack (aux) connected to the PlayStation controller. USB models will also work on PlayStation. In addition, the wireless models works wirelessly when connected to the 2.4GHz USB dongle.

Please note: JBL QuantumENGINE is only available on PC. Custom lighting can be set up on PC, and will carry over when connected with USB cable or 2.4GHz USB dongle. 

Press and hold the power button located on the RIGHT ear cup. Make sure that the device is on and in Bluetooth range. If this is the first time connecting the device, it will automatically go into pairing mode. You will notice the LED light alternate between blue and white as it searches for a device to connect to. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect.

Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.

To increase battery life on your Quantum headphones, turn off your RGB lighting as this will help increase the wireless playback time. You can turn off the RGB in the QuantumENGINE or press and hold the mute button on the headset. 

Only the primary speaker prompts the user when pressing the association button. This does not happen when the same is done on the secondary speaker. However, the front panel LED blinks quickly, indicating that association process is taking place. (This applies to primary and secondary speakers both.)

The Recommended Retail Price (RRP) is a pricing suggestion provided by the manufacturer or supplier of a product. It indicates the price at which the manufacturer suggests the product should be sold in the retail market. The RRP is often used as a reference point for consumers and retailers.

Retailers are not bound to sell products at the RRP. Retailers may choose to sell the product at a higher or lower price depending on various factors, including market conditions and promotional strategies.

The JBL web shop always introduces new products at the RRP but may deviate from the RRP after introduction depending on the factors described above.

When a promotion is shown, the crossed-out reference price and/or the savings percentage are based on the lowest price listed on the JBL web shop in the 30 days prior to the promotion.

Reset the Soundbar by the same process as when doing "reset remote settings": 1. Switch the SB 350 ON. 2. Press and hold the Surround and Volume (–) buttons simultaneously for about 3-4 seconds, then let go. The Source selection Button flashes amber, followed by the power button and source buttons flashing several times. 3. The soundbar is now reset.

Looking to register your product?
We have addressed some of the questions that you might have. But feel free to reach out to us anytime you need us!

Where can I register my product?
Visit our product registration page.


Do I need to register my product for warranty?
No. Warranty is never depending on the registration of a product. Registration simply helps keep a record of your purchase(s) and gives you the opportunity to stay update on any information about your product(s).


Do I need an account to register my product?
Yes. We have made it easy to create an account for you so you can enjoy the benefits of having an account, including the option of registering your product.



Already registered a product and have questions?
Go no further! We hope you can answer your questions below. If needed, get in touch. We are always here to help you!

Can I edit an existing product registration of mine?
Partly, yes. You can edit the “Date of purchase” and “Serial Number” fields.

To do so, log into your account and select "My Product Registrations", find the relevant product from your list of registrations and select “View Registration”. Here you will find the option “Edit registration”.

If you wish to make changes to any other fields, please delete the relevant registration completely (see instructions below) and simply create a new registration.


Can I delete an existing product registrations of mine?
Yes. To delete an existing product registration, you can use the “Delete registration” option.

Log into your account and select "My Product Registrations", find the relevant product from your list of registrations and select “View Registration”. Here you will find the option “Delete registration”.
 

The intensity of the light show is dependent on the amount of audio signal being sent into the unit.

If you are experiencing a light show that doesn't move around very much, it is likely that you are not using a feature on your phone called Bluetooth Absolute Volume*. This means that the volume of your phone/tablet/device is controlled independently from the volume of the speaker.

So, if you have the Pulse 4 set to maximum volume or close to it, but the volume on your device is set at a low level, the light show will show little to no effect. All you have to do is reverse it. Turn up the volume on the device to the maximum and set the Pulse 4 to the desired volume. This will send the correct level to the speaker and the light show will show plenty of effect. This also benefits the sonic quality as well. Therefore, we recommend always having the volume on your device turned up to a high level and then adjusting the volume level on the speaker itself. This way you'll be able to enjoy the light show while also getting good audio quality. Or, if possible, setup your device for Bluetooth Absolute Volume*.

*BLUETOOTH ABSOLUTE VOLUME: Most phones/tablets/devices now use Bluetooth Absolute Volume (a.k.a. volume sync) by default. This is a feature that synchronizes the volumes of the device and the speaker, and allows the speaker volume to be controlled by changing the volume on either the device or the speaker. The volume being sent from the device is fixed at full volume.

A new firmware version has been released for the Pulse 4 (Version 0.5.1.0), below is a list of the improvements:

1. Supports Bluetooth 5.1 profile.
2. Improves the stability of stereo setup using the JBL Portable* app.
3. Improves compatibility with Mac computers.
4. Enhances light show synchronization with music.

The firmware update is installed as an OTA update:

1. Download and install the JBL Portable* app from the Google Play/App Store.
2. Connect your Pulse 4 to your phone/tablet through Bluetooth.
3. Open the JBL Portable app and wait for the Pulse 4 to appear.
4. On the Pulse 4 screen, select settings (gear cog symbol).
5. Proceed with installing the firmware update.

*JBL Portable is the new name for the JBL Connect app, the name will change in January 2021.

Press and hold the Light Show & Bluetooth buttons together for > 2 seconds.

Press and hold the Light Show & Bluetooth buttons together for > 2 seconds.

QUANTUM DUO
Software Update Release Notes
------------------------------------------------------------------------
Version:  V46
Release Date:  August 31, 2022
Release Media:  USB
Filename:  JBL Quantum Duo SW release V46.zip

What's New

1. We have improved the volume synchronization between the Quantum DUO and Windows OS, which give the user a better sound experience

------------------------------------------------------------------------
------------------------------------------------------------------------

QUANTUM DUO
Software Update Release Notes
------------------------------------------------------------------------
Version:  V44
Release Date:  December 15, 2021
Release Media:  USB
Filename:  JBL Quantum Duo SW release V44.zip

What's New

1. Allow user to disable the auto standby feature via long pressing lighting pattern and right color selection button for >10 seconds
2. General Software Improvements

QUANTUM ENGINE 

Software Update Release Notes 

Version 1.6.0.1053
Release Date: 1/21/21
 

1. Welcome feature has been implemented.

2. Surround Modes feature has been implemented.

3. ANC/TT toggle has been implemented.

4. The sidetone has been turned off by default for all models to avoid confusion.

5. QuantumSURROUND/QuantumSPHERE quality & performance have been improved.

6. Quantum 300 Mic Gain has been improved.

7. Quantum 800 FW update reliability has been improved.

8. Minor Bugs Fixed 

 

 

QUANTUM ENGINE
Software Update Release Notes
------------------------------------------------------------------------
Software Version:  V1.11.0.1511
Release Date:  September 19, 2022
Release Media:  Website & Quantum ENGINE

What’s New

1. Improved firmware stability upgrading process flow for the QUANTUM 910.

------------------------------------------------------------------------
------------------------------------------------------------------------


QUANTUM ENGINE
Software Update Release Notes
------------------------------------------------------------------------
Software Version:  V1.11.0.1510
Release Date:  August 24, 2022
Release Media:  Website & Quantum ENGINE

What’s New

1. Added support for the new QUANTUM 910 Wireless Headphones
2. Over 30 improvements addressing user interface, usability, and stability of the app for a better user experience.

QUANTUM STREAM STUDIO

Software Update Release Notes

------------------------------------------------------------------------

Version:  1.4.9

Release Date: January 13th, 2025

Release Media: OTA (over the air) Update via JBL QuantumENGINE

 

What’s New

1. Zoom USB Certified
2. Stability and performance improvement

 

QUANTUM STREAM TALK

Software Update Release Notes

------------------------------------------------------------------------

Version:  1.4.9

Release Date: January 13th, 2025

Release Media: OTA (over the air) Update via JBL QuantumENGINE

 

What’s New

1. Zoom USB Certified
2. Stability and performance improvement