How To
How To
-
This model is supported by the JBL Partybox App.
Download the JBL Partybox App from the App Store or Google Play Store and install it to use the following features:
SETTINGS: OTA update | Firmware Version | Quick Start Guide
REMOTE CONTROL: Music playback – Play/Pause & Skip Track | Karaoke – Bass/Treble/Echo | DJ sound effect – Here you can swap which samples will play when you hit the three Sound Effect buttons on the top panel, or play all of the available sounds on one screen | Top panel control | Source select | Bass Boost – On/Off
LIGHT SHOW: Fully customize your light show in real time – Change light themes and animations to suit your mood | Turn animations on or off | Turn the strobe on or off | Customize color (preset or color palette) | SOLO mode
GET LOUD: Connect in TWS, switch Stereo channels and enable Party ModeWas this helpful? Thank you for your feedback! -
This headphone does not feature volume control. You must manually control volume from your device.Was this helpful? Thank you for your feedback!
-
Yes, that is possible. 1: Turn on your Cinema Base. 2: Press surround and volume - button simultaneously for 5 seconds. 3: When the source button on the Cinema Base lights amber for 1 second and goes off after. 4: Your Cinema Base is now reset.Was this helpful? Thank you for your feedback!
-
JBL BAR Setup App (for Bar 5.1 Surround)
Software Update Release Notes
------------------------------------------------------------------------
Version (iOS): 1.0.9431 (2208021531)
Version (Android): 1.0.11129
Release Date: August 22, 2022
Release Media: App Store (iOS & Android)
What’s New- Improved Amazon Account setup experience
- Improved the overall customer experience
Was this helpful? Thank you for your feedback! -
Please check with your car manufacturer to ensure your car supports CAN or K-line. JBL DRG only works with CAN and K-line to get the engine data for engine sound simulation. If your car does support CAN or K-line, please launch the JBL DRG app and check the engine sound volume bar (the right column with button marked with “E”) in the “Sound Mode” section to make sure it is not turned off.Was this helpful? Thank you for your feedback!
-
Please use an OBD II extension cable in this case. An extension cable is not included in the package but they are readily available for purchase on-line.Was this helpful? Thank you for your feedback!
-
When you place the two Free earphones in the charging case, you will see a white led ring light up on both of them. At the same time, some of the four dot-leds on the charging case will light up to indicate the battery level of the case battery. When the earphones are fully charged, the white led ring goes out on each of them. When both are fully charged, the charging case charging level leds go out too.Was this helpful? Thank you for your feedback!
-
The JBL Free automatically switches from stereo to mono when making or taking phone calls. Voice calls will only come through the right ear piece for a more natural call experience.Was this helpful? Thank you for your feedback!
-
In the event that left and right ear piece pairing is lost, power on both ear pieces and press the buttons 3 times on each ear piece to initiate re-pair.Was this helpful? Thank you for your feedback!
-
In the event that ear pieces do not re-pair automatically to paired Bluetooth device, power off ear pieces individually by press and hold the buttons for 5 seconds. To enter Bluetooth pairing mode when ear pieces are powered off, press and hold on buttons of both earpieces for 8 seconds. Re-pair the right ear piece with desired Bluetooth device when LED indicator on right ear piece alternates between blue and white LED lights.Was this helpful? Thank you for your feedback!
-
Remove ear pieces from the case. Both ear pieces should automatically connect to each other. Wireless connections are automatically established when the headphones are taken out of the case. To pair to a different device, press and hold the Right ear piece for 5 seconds as it alternates between blue and white LED lights. Make sure that the device you are attempting to connect to is in pairing mode. The JBL Free should display on discoverable devices within 3-8 seconds. Choose JBL Free and the headphones will connect after you hear the audio confirmation tone.Was this helpful? Thank you for your feedback!
-
Remove the Right ear piece from the case. (It should automatically enter into pairing mode and will alternate between blue and white LED) Make sure the unit you are trying to connect to is in pairing mode. It should recognize the JBL Free within 3-8 seconds. Choose "JBL Free" to connect.Was this helpful? Thank you for your feedback!
-
The JBL Free has an IPX5 rating that helps protect the headphones from sweat and moisture.Was this helpful? Thank you for your feedback!
-
The JBL Free X does not feature volume control. In order to adjust the volume, you must manually increase/decrease from your device.Was this helpful? Thank you for your feedback!
-
PSAP (Personal Sound Amplification) is a new feature accessible within the JBL Headphones App. When this feature is turned on, it works similar to Ambient Aware, but it focuses on picking up vocal frequencies in front of you.
1. GAIN: The Personal Sound Amplification function is designed to amplify sound in the vocal range, it can assist users with (limited) hearing loss to maintain conversations more easily, especially in noisy environments. It should then amplify the speech of the person sitting across from you, not the general ambient sound as with Ambient Aware. The algorithm uses beamforming to pick out the voice from the other sounds, much like what happens during a phone call, but instead of focusing on your own voice it focuses on the voice further away from you. The gain setting allows you to amplify those vocal frequencies.
2. BALANCE: The balance setting adjusts the amplification effect between your left and right ears using the slider. When set to 0 (in the middle), both ears will receive the same amplification, but depending on the user’s personal needs/preferences, they can focus the amplification more towards either the left or right ear.
Was this helpful? Thank you for your feedback! -
Personi-Fi 2.0 is a new feature available through the JBL Headphones App. This feature helps to personalize the sound using the best possible sound curve based on your hearing capabilities. It will first ask a few questions, and then check your current ambient audio. You will be informed that this step should be completed in a quiet environment. It will play a series of test tones in all the different frequencies wherein after each frequency test tone is played, it will ask you what is the lowest volume setting you can hear. Nine different sounds will be played in each ear (18 in total).
Simply press and release the button when you hear a sound. After it goes through all the test tones, it then calculates the best sound for your ears based on the results. It allows you to demo the results by playing a track. You will be able to toggle it on/off to hear the difference.
Was this helpful? Thank you for your feedback! -
Rated Power Output
Partybox 110:
AC Power 160W
DC Power (battery) 100W
Partybox 200:
AC Power 120W
12V (car) 90W (PLEASE NOTE: NO BATTERY)
Partybox 300:
AC Power 120W
DC Power (battery) 90W
12V Power (car) 90W (PLEASE NOTE: DOES NOT CHARGE THE PARTYBOX, ONLY POWERS)
Partybox 310:
AC Power - 240W
DC Power (battery) - 140W
12V Power (car) - 140W (PLEASE NOTE: DOES CHARGE THE PARTYBOX)Was this helpful? Thank you for your feedback! -
You cannot download the JBL Portable App on a PC. This app is only available on mobile devices.Was this helpful? Thank you for your feedback!
-
JBL PORTABLE App
Software Update Release Notes
------------------------------------------------------------------------
Version (iOS): 5.6.7
Version (Android): N/A
Release Date: September 13, 2022
Release Media: App Store (iOS)
What’s New- Solved the issue that iOS 16 users could not use JBL PORTABLE App
Was this helpful? Thank you for your feedback! -
The single ANC/TalkThru button accomplishes several tasks, turning the ANC on and off, and turning the TalkThru on and off. It behaves slightly different than you might expect. Here is a description of how to accomplish each task.
To turn ANC on and off
Short Press: ANC On (voice prompt states ANC On)
Short Press: ANC Off (voice prompt states ANC Off)
To turn TalkThru on and off
Long Press: TalkThru On (voice prompt states TalkThru On)
Short or Long Press: TalkThru Off, but ANC is now On (voice prompt states ANC On)
Short Press Again to turn ANC Off as well (voice prompt states ANC Off)
NOTE: The voice prompt will never state that TalkThru is Off.
Was this helpful? Thank you for your feedback! -
You can adjust Equalizer, Spatial Sound, RGB LED effects, change microphone settings and update the headset's firmware
Was this helpful? Thank you for your feedback! -
JBL Quantum Headphones Upgrade tool redefines your headphones experience. Through your macOS device, you can now conveniently upgrade the headset.
Download from macOS app store: https://apps.apple.com/us/app/jbl-quantumengine/id1645040444
Supported models are:- JBL Quantum 610
- JBL Quantum 810
- JBL Quantum 910
- JBL Quantum 910P
- JBL Quantum 910X
- JBL Quantum TWS
Was this helpful? Thank you for your feedback! -
The JBL Trip visor mount is bi-directional. Mount the clip to the other side of visor as shown in the “quick start guide” section 8. This will help displace the weight differently and your issue should be solved.Was this helpful? Thank you for your feedback!
-
The JBL Xtreme will not be supported by the JBL Portable app while using Apple devices with iOS 14 or later versions due to incompatibility.
You can continue to use the speaker through Bluetooth or Aux connection and manual pairing, but cannot stereo pair with another Xtreme through the JBL Portable App.
There is no plan to release a new Firmware currently as the JBL Xtreme has been discontinued.
If you still wish to use JBL Xtreme with the JBL Portable app, please connect it with Apple devices with iOS 13 or below, or connect it with Android devices.Was this helpful? Thank you for your feedback! -
The Checklist
Let us walk-through a list of things needed to ensure every requirement is met.
- Check your mobile device if that is able to connect to same Wireless network.
- Make sure you are within range of your Wireless router.
- Check the Wireless signal on your mobile device, does it have a weak signal then move closer to the router.
- Try both Wireless network bands 2.4GHz and 5GHz in case one of them are failing.
- You will have longer range with 2.4GHz, but less performance and most of the times a crowded network (many devices are using 2.4GHz band).
- You will have less interference with 5GHz and higher performance, however, the range of the 5GHz network has shorter range.
- Try using a different mobile device, if you have one.
- Reboot your Wireless network router and your mobile device.
Wireless Network Extender
Some houses or apartments can be too big for one Wireless network router to cover it all.
Let's talk about the issues that might appear with an Extender network.- Network Extenders that will help cover poor signal in your home, often results in poor connection and low speed performance.
- Often the Network Extender is a low budget device or not suited for having too many devices attached to it.
- Placement of the speaker is crucial as you can put it in a place where it could connect to either main Wireless router or the Extender, that will confuse Wireless network devices.
- To solve this issue, try move the speaker closer to main router or have fewer devices attached to your Wireless Extender.
- In addition, always use 5GHz connection between your Network extender and main router (best solution and performance).
One Wireless Network Name (SSID)
- You may have set the Wireless Network SSID (Wi-Fi network name) to one big Wireless network (With a main router + Extender(s).
- If the speaker is within range of both Wireless networks (Main router & Extender) then it can get confused with which one to connect to.
- To solve this issue, using two different name for your extended network will help with the performance of the Speaker and Google Assistant request.
Was this helpful? Thank you for your feedback! -
If the left ear pod is silent, please perform a new pairing with the right pod like shown in the quick-start guide.
Take them out of the charging case and click the center button on both the left and the right pod 3 times.
This forces a new pairing between the pods, and the left pod should automatically pair with the right pod from now on once you remove both pods from the charging case.
If you still cannot get the Left ear to play, please perform a factory reset by placing both pods in the charging case, while the charging case is charging. Now press the button on the right pod, and hold it for more than 5 seconds. You have now reset to factory settings. (Please note: If you have performed a factory reset, you will need to remove the headphones or "forget this device" from any smart phone or tablet they were once connected to. This will allow your device to now search for the newly restored headphones under BT devices)
The right pod is the primary, which is connected to your source, usually a smartphone.
The left pod is the secondary, which connects to the right pod.
Was this helpful? Thank you for your feedback! -
LIVE FREE 2 TWS
Software Update Release Notes
------------------------------------------------------------------------
Software Version: V6.9.8
Version (iOS): V5.7.9
Version (Android): V5.7.9
Release Date: July 8, 2022
Release Media: OTA via JBL Headphone App
What’s New- Added Microsoft Swift Pairing feature.
- Fixed a few minor software bugs for better user experience.
Was this helpful? Thank you for your feedback! -
The Left and Right bud should sync together automatically when removed from the case. If the Left and Right bud do not sync together automatically within 15 seconds, you may manually sync the buds together. With the buds out of the case, press the center button on each bud 3x. This action does not have to be done simultaneously. You may start with either the L or R bud to initiate syncing.Was this helpful? Thank you for your feedback!
-
Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. And the default setting of the mic monitoring is set of “OFF”.
Was this helpful? Thank you for your feedback! -
Yes. You can configure the volume of the mic monitoring in JBL QuantumENGINE. The default setting of the mic monitoring is "OFF”.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Call us
Call us now at:
+45 32712498
Monday - Friday: 09:00 - 17:00
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00