How To
How To
1078 results
-
First, it is very important that you use the correct size enhancers (rubber tips). This headphone features the TwistLock technology that is uniquely designed to fit in the bowl of the ear (vs. inner ear). They may look bigger than traditional earbuds, but this design provides the most secure fit to ensure they never fall-out in the most active workouts. To properly put them on, first make sure you have the Right and Left earbud in the correct ear. The number to indicate the enhancer size is featured on the inside of the enhancer next to the large L or R (left ear, right ear). Next, gently insert the enhancer into your ear with a forward motion towards the jaw, which should twist and lock the enhancer into place. These headphones come with 5 sizes of fit enhancers (4, 5, 6, 7 & 8) and 3 sizes of ear tips (small, medium & large). The fit enhancers sit in the bowl of your ear and are essential for a secure fit, while the ear tips are inserted in the inside of the ear canal and provide sound occlusion. The size 7 fit enhancer and large ear tip comes pre-installed on the headphone. If you experience discomfort wearing the size 7, try the next size down. If you try a smaller size and the headphones fall out easily or the enhancer does not extend fully to the back of the bowl of the ear, you should try a bigger size.Was this helpful? Thank you for your feedback!
-
For the best performance, connect the speaker to a power outlet.
Was this helpful? Thank you for your feedback! -
After the wake-up process is finished, and the radio alarm has been turned off by pressing the alarm button, it is necessary to press the radio button to keep the radio playing.Was this helpful? Thank you for your feedback!
-
As the headphones are charging, you will see a red solid light indicator at the bottom LEFT ear cup. Once the unit is fully charged, the red light will turn off.Was this helpful? Thank you for your feedback!
-
You will hear an audio prompt to readjust the position of the left ear piece stating “heart rate not detected, adjust ear bud position”. The sensor is also in the correct position when the green LED light is not visible from the outside of your ear.Was this helpful? Thank you for your feedback!
-
By habit, we try to shove earbuds into our ear canals in attempts to get them to stay in. The 500 Series headphone is a completely different concept. The tip of the enhancer (ear tip) should funnel gently down into the ear canal and the base of the enhancer should fill the entire concha (bowl) of your ear. If there is still quite a bit of space between the back of the enhancer, and the back of the bowl of the ear, there is nothing to support it and it will eventually fall out. Typically larger sizes will fill the extra space inside the concha. We recommend trying both sizes featured in the packaging. If you are still experiencing fit issues, please reach out to your local JBL Customer Support for information regarding different sizing options.Was this helpful? Thank you for your feedback!
-
Select the UA Sync icon in the upper right hand corner of the dashboard. If your headphones are connected, they will appear under "My Apps and Devices". Tap on "UA Sport Wireless Heart Rate" and you will see your headphones settings. Your headphones' battery life appears in the top left corner. If you have an IOS device, you also will be able to see the battery life indicator in the upper right hand corner next to the BT symbol. Additionally, you should hear the audible voice stating ‘low battery’ when you have 15-20 minutes left of battery life left on the headphones.Was this helpful? Thank you for your feedback!
-
The Flip 3 SE has 5 white leds which shows the battery level when you power on the device. Each white led indicates around 20% battery level. When all of the white leds are off, and the last led is blinking red, you should recharge the battery.Was this helpful? Thank you for your feedback!
-
When the headphones are charging, you will see a solid red light at the top of the inline microphone. When the headphones are fully charged, the red light will shut off. You should expect 8 hours of playback time. Please keep in mind that the level of volume can effect the longevity of the battery life.Was this helpful? Thank you for your feedback!
-
After you set up Alexa and Google Assistant via the JBL One app, you will see examples of what you can do with each assistant. For more information on what each voice assistant does, visit Alexa Features or Explore Google Assistant .
Was this helpful? Thank you for your feedback! -
Tap once on the JBL logo of the right earbud, then place your finger on the logo again, and hold it there for 5 seconds. You will hear a confirmation tone in the headphones when locking takes place. To unlock, close the power hook.Was this helpful? Thank you for your feedback!
-
To ensure the best accuracy, it is important that you are using the proper size and the headphones securely fit in the ear. Please reference FAQ: How do I find the proper fit? to make sure you are wearing them correctly. You should also make sure that the enhancers are properly installed on the ear buds so that material is fully stretched over the bud and the window for the heart rate (HR) sensor is not covered. Please reference FAQ: How do I switch enhancer sizes? for more guidance. Once you've found your ideal size and ensure they're installed correctly, make sure the HR sensor is on. When it is on, you will see a green light on the LEFT ear bud and should hear the audio prompt stating, “Heart Rate sensor on”. For best results, insert the earphone into your ear so that the green heart rate sensor on the LEFT ear bud is fully hidden inside the ear (behind your tragus). Double check that the ear bud is touching the back of the bowl of your ear for the most accurate signal - this is often times achieved by using the largest size that fits comfortably in your ear. Lastly, the ear loop should not be pushed backwards to align with arc of the ear perfectly; it is likely there will be negative space between the headphone loop and your ear. You should hear the audible alert telling you if the ear bud needs to be adjusted if it is unable to retrieve a proper reading on your heart rate. Heart Rate accuracy can vary depending on the type of exercise you are performing; it is recommended for steady state endurance-oriented activities to ensure best accuracy. While the technology is state-of-the-art, there are limitations that may cause some readings to be inaccurate under certain circumstances. These circumstances include physical characteristics, fit, and the type of activity as outlined above. The heart rate monitor data is not intended to be used for medical purposes, nor is it intended to diagnose, treat, cure or prevent any disease or condition.Was this helpful? Thank you for your feedback!
-
During phone call, short press the Siri Access button shown in “quick start guide” section 6 to mute the microphone. A short press the same button again will un-mute.Was this helpful? Thank you for your feedback!
-
Short-press the Bluetooth Button to activate pairing mode. Now set your device to scan for Bluetooth devices. It will find the BOOST TV and allow you to pair to it.Was this helpful? Thank you for your feedback!
-
Short-press the Bluetooth Button to open for new pairing.Was this helpful? Thank you for your feedback!
-
Swift Pair is the newest way to pair your Bluetooth peripherals Windows 10, version 1803 or above.
Steps:
1. Put the Bluetooth peripheral in pairing mode
2. When the peripheral is nearby, your Windows device will show a notification
3. Selecting “Connect” starts pairing the peripheral
4. When the peripheral is no longer in pairing mode or is no longer nearby, your Windows device will remove the notification from the Action Center
Was this helpful? Thank you for your feedback! -
Simply hold Bluetooth button on the remote and once its start flashing, on your device go to your Bluetooth settings and look for the gtr amp and pair it.Was this helpful? Thank you for your feedback!
-
The SB450 soundbar is paired to the subwoofer right out of the box. If the 2 parts are not already paired together, simply press the Pairing buttons on the rear panel of both products and they will connect with each other.Was this helpful? Thank you for your feedback!
-
Power on the Flip 3 SE and press the Bluetooth button. The Flip 3 SE should be available in the list of Bluetooth devices on your mobile phone/tablet.Was this helpful? Thank you for your feedback!
-
Normal pairing is automatic, and happens when you first switch both devices on. If pairing does not take place automatically, or you have to force new pairing, here is what to do: Turn on the soundbar and the subwoofer. If the connection is lost, the LED indicator on the subwoofer blinks slowly. Second, press the CONNECT button on the subwoofer to enter pairing mode. The LED indicator on the subwoofer blinks quickly. Third, press and hold the DIM DISPLAY button on the remote control for 5 seconds, followed by short press on BASS+, and BASS- button in sequence. Panel display will show “PAIRING”. If pairing succeeds, the LED indicator on the subwoofer lights up, and the soundbar display will show "DONE”. If pairing fails, the indicator on the subwoofer blinks slowly. Lastly, if the pairing fails, repeat the steps above. If you have continued trouble performing the pairing, please try to switch off all wireless devices in the home, then try again. This means routers, TV sets with wireless functions, telephones, computers etc. Since overcrowding on the 2.4 GHz frequency now often causes problems, eliminating all this activity makes space for the Bar to establish its connection, and you should be able to pair without problems. Afterwards, you can switch your devices on again. Often, all will now work fine, and if not, you will know which devices are doing the interference.Was this helpful? Thank you for your feedback!
-
To pair to a different device, double tap and hold your finger on the JBL logo for 5 seconds until you see the LED light flash blue. Make sure that the device you are trying to connect to is in range and in pairing mode. You should see the Endurance headphone pop up on your discoverable devices within a few seconds and the flashing LED light should now be a solid blue.Was this helpful? Thank you for your feedback!
-
In order to pair to a different device, make sure the headphones are turned off. Proceed to press and hold the power button located on the LEFT arm of the neckband. You will hear the audio voice prompt state, “powering on” Continue to press and hold the power button for 3-5 seconds or until you hear the voice prompt state, “looking for device.” Make sure that the device you are attempting to connect to is in the Bluetooth search mode and within range. UA | JBL Flex should appear on your device within 3-8 seconds. Once you choose this option on your discoverable devices, it will connect and the voice prompt will state “Connected”Was this helpful? Thank you for your feedback!
-
Press and hold the center button on the inline microphone located below the right earpiece. It helps to have one of the ear inserts in your ear to listen to the audible voice prompts. If this is your first time using the headphones, the headphones will automatically go into search mode. You will hear the audible voice stating, “power on” followed by “looking for device”. To power off, press and hold the center button on the inline microphone until you hear the audible voice stating, “power off.” The flashing LED light should change to a solid red light before completely turning off.Was this helpful? Thank you for your feedback!
-
Press and hold the center button on the inline microphone located below the right earpiece. It helps to have one of the ear inserts in your ear to listen to the audible voice prompts. If this is your first time using the headphones, the headphones will automatically go into search mode. You will hear the audible voice stating, “power on” followed by “looking for device”. To power off, press and hold the center button on the inline microphone until you hear the audible voice stating, “power off.” The flashing LED light should change to a solid red light before completely turning off.
Was this helpful? Thank you for your feedback! -
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure the E65BTNC headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Press and hold the center button located on the inline microphone. It helps to have one or both ear inserts in the ear to hear the audio voice prompts. Once you press and hold the power button, you will hear the audio voice stating, "powering on". If this is your first time pairing the device, it will automatically go into pairing mode and will be looking for the device. Make sure the device you are trying to connect to is in search mode. It should recognize the Everest 110 within 2-3 seconds. If you would like to connect to a different device. Make sure the unit is off and proceed to press and hold the center button on the inline mic from 4-6 seconds until you hear "powering on......JBL Everest is ready to pair. Go to the pairing menu on your device" You will now be able to pair to a different device. The device should recognize the Everest 110 within 2-3 seconds and will connect.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Locate the power button on the back of the right ear cup. Gently slide the spring loaded power button up and release. Once turned on, it will display a solid white light. If this is your first time powering on the device it should automatically go into pairing mode, and will display a fast blinking blue light. Make sure the device you are attempting to connect to is in search mode. The headphones should pop up on your list of discoverable devices within 3-5 seconds, and connect. If you are attempting to pair to a different device, make sure headphones are turned on, and press and hold the Bluetooth button located at the bottom of the right ear cup. The headphone should display on your new device within 3-5 seconds on your list of discoverable devices.Was this helpful? Thank you for your feedback!
-
Press the power button located on the far Left top of the speaker. If this is your first time pairing the device, the speaker will automatically go into pairing mode. Make sure that the product you are attempting to pair to is in search mode and in bluetooth range. The Go 2 should pop up on discoverable devices. Choose the Go 2 option and you will be connected within a few seconds.Was this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00
