How To
How To
1096 results
-
If the pairing mode is not succesful, please move the subwoofer closer to your SB150. The pairing process can take up to 30 seconds before a connection has been established.Was this helpful? Thank you for your feedback!
-
Please check that Google Assistant or Amazon Alexa are installed on your device.
Try to repeat the setup process.
Also, switching the headphones off and on once or twice may solve the problem.Was this helpful? Thank you for your feedback! -
Please check Google Assistant or Amazon Alexa are installed on your device. Try to repeat the setup process. Also, switching the headphones off and on once or twice may solve the problem.
Please note that these services can only be activated from the earphone's buttons when the headphones are connected via Bluetooth. Buttons on a cabled remote cannot be used for this purpose.Was this helpful? Thank you for your feedback! -
It sounds like you are living in a country where Google Assistant has not yet been officially released. When Google releases the Google Assistant to more countries, the Everest GA headphones will open up for this feature. It may require a software update for this to happen. For now, you can use them as normal Bluetooth headphones and wait for the release to use the Google Assistant feature.Was this helpful? Thank you for your feedback!
-
The TV turns on with the soundbar. This is caused by CEC commands from your TV via the HDMI port. Please disable these functions on your TV, to use the soundbar while TV is off.Was this helpful? Thank you for your feedback!
-
To use Chromecast, you must continue the setup in the Google Home app first.
Configuring the speaker only with Apple WAC will not enable the Chromecast feature.
For this to happen, you must sign-in with your Google account.
You can quickly try out the Chromecast feature, and if you do not like it, reset your Citation or LINK speaker, and redo the configuration part on your Apple device.Was this helpful? Thank you for your feedback! -
Please keep the app running during a firmware upgrade. This is because the app is using BLE to transfer firmware to the JBL DRG. If you exit or kill the app, this will cause the BLE connection to be broken and the upgrade will not complete.Was this helpful? Thank you for your feedback!
-
To use the Spotify Connect feature for JBL Playlist, a premium Spotify account is required. Please visit www.Spotify.com/freetrial for 30 days of complimentary premium account trial for first time users.Was this helpful? Thank you for your feedback!
-
JBL DRG will auto reconnect to the last device. To setup a connection with new Bluetooth head unit, press the “reset” button in the App. The device will then search for a discoverable Bluetooth connection and setup.Was this helpful? Thank you for your feedback!
-
Close and reopen the app. This will ensure that the app recognizes the headphones.Was this helpful? Thank you for your feedback!
-
The JBL Charge 3 has a battery level indicator, which consists of 5 LED's and display battery level.Was this helpful? Thank you for your feedback!
-
The 4 LED's on the front of the unit will light up.Was this helpful? Thank you for your feedback!
-
It is offering low-latency wireless connectivity via a 2.4Ghz signal that is enabled by a USB dongle included in the box. Turn on the slider, then it automatically connect to the dongle. If you loss the connectivity with the dongle, power on with the slider and hold on for 5 seconds and press and hold the dongle to make sure the pairing until listening to the tone. Was this helpful? Thank you for your feedback! -
After setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.
Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones
Get your notifications
Double-tap the Action button.
Stop your Google Assistant
Touch the Action button.
Reply to the message (where available)
After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.
For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones
Was this helpful? Thank you for your feedback! -
This video shows how to use a smart speaker that has Google Assistant built-in.
Our LINK series have Google Assistant built-in therefore you can practice your voice commands together with Harman/Kardon Citation or JBL LINK products
Was this helpful? Thank you for your feedback! -
After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
Things to try- “What’s the weather?”
- Play Niall Horan
- Play NPR on iHeartRadio
- Set a timer for 5 minutes
- What new skills do you have?
While Alexa is talking, press and release the Action button then say “Stop”.
For more information and things to try with Alexa, visit: www.amazon.com/alexadevicesWas this helpful? Thank you for your feedback! -
- On an Android or iOS device, add the Soundbar to your home WiFi network through the JBL BAR Setup App.
- Follow the App instructions to complete setup.
- Sign in with your Amazon Alexa account. If you do not have, create one.
- With the Alexa MRM multi-room music playback, you can stream music on your Android or iOS devices to multiple Amazon Alexa speakers.
Was this helpful? Thank you for your feedback! -
The remote control included with your LINK BAR can be updated, if a new version becomes available for your device.
There are two ways to find out if an update is available.- A notification on your Android TV screen will appear. When clicking on it with your remote, more information will pop up.
- Manually check for an update, in case you have dismissed the notification, or the system does not show it.
To manually check for an update, please follow the instructions.
1. Go to "Settings" on your Android TV (ICON)
2. Find Connected Devices
3. Click on LINK BAR Remote
4. Under the Update firmware, if there is an update available, you will see it under the name.
The latest firmware version for your remote control is 1.27 (Changes to firmware numbers will change in the future).
5. Confirm the update for your remote control. The system ill download the files, and automatically start to update your remote.
5.1 NOTE: The battery needs to have more than 20% power left. If your remote is under 20%, you need to change the batteries, as this may break the remote control device.
6. When the update is ongoing, you must keep the remote control near the LINK BAR. This is because the remote is using Bluetooth to communicate with the system, and updating the device happen through Bluetooth connection. The update may take around 10 minutes or less.
7. When update is complete, this message "Remote is up to date," is visible, and you have the latest firmware.Was this helpful? Thank you for your feedback! -
You can update our Quantum 600 and 800 using the QuantumENGINE software on your PC.
To update the headset, go to SYSTEM SOFTWARE tab, find section HEADSET, and press CHECK FOR UPDATE and then INSTALL UPDATE.Was this helpful? Thank you for your feedback! -
To turn on/off the TV, the recommended control is “OK Google, turn on”/”OK Google, turn off.”
Note that this depends on your TV manufacturer and if they support this via HDMI CEC (This works only for HDMI connection).Was this helpful? Thank you for your feedback! -
1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).Was this helpful? Thank you for your feedback!
-
Press and hold the Lightshow button for more than 2 seconds to turn off the Lightshow.Was this helpful? Thank you for your feedback!
-
Once an alarm is set and starts to ring, it can be snoozed by tapping the large central knob/button on the top of the unit (circled in yellow in the image below). If this button is held for more than 2 seconds it will turn off the alarm.
The duration of the snooze cannot be changed and is fixed to 9 minutes. The alarm will continue to ring for 3 minutes and if not turned off or snoozed, it will automatically snooze after this time. It will automatically snooze for a maximum of 3 times, but if the snooze button is used before this occurs, the alarm can be snoozed an unlimited number of times.
Once snoozed, the display shows the time that the alarm will next ring.
To keep the radio playing after the alarm is turned off, press one of the 3 preset buttons or the DAB/FM button as desired.Was this helpful? Thank you for your feedback! -
The voice assistant you select in the initial set-up (pictured below) will be used as the default assistant on your headphones.
You can change the default assistant in the ‘My JBL Headphones’ app:- Open the My JBL Headphones app on your device.
- Select the headphones you are connected too.
- Go to Settings by clicking the symbol in the top right corner.
- Select Voice Assistant.
- Now you can select your preferred voice assistant.
Your headphones may restart after switching Voice Assistant.Was this helpful? Thank you for your feedback! -
Yes, you can adjust the game and chat audio balance by rotating the dial-up and down. When you rotate the dial, you'll feel a notch that indicates the balance is 50% game and 50% chat. The slider on Quantum ONE is different and has no notch but instead a visual indicator.Was this helpful? Thank you for your feedback!
-
Onboard Active Noise Cancelling is controlled by the multi-function button on the rear of the left ear-cup. Switched on by default, you can SINGLE press the ANC button to toggle it On/Off and LONG press to active TalkThru. Turn on ANC again by a single press on the multi-function button.Was this helpful? Thank you for your feedback!
-
Our new JBL Link Music and Link Portable both support Apple AirPlay 2. Pick up your Apple device, use your favorite music streaming service, and connect to the JBL speaker! Please note: before using Apple AirPlay 2, you will need to install it on your WiFi network, either using the Google Home app or Apple Home app ( your choice! ).Was this helpful? Thank you for your feedback!
-
To show the current firmware version on your JBL TUNER device, go through the following steps.
- Turn on the JBL TUNER.
- Press and hold this three-button combination: DAB/FM+ Volume+ and Preset 5, simultaneously for 3-4 seconds.
- In the display, you will see a combination of letters and numbers. This is the current software version.
- See picture below as illustration.
The new firmware version released is V.0.0.57 (shown in the picture above).
To get the latest version, ask our customer service for a guide and an upgrade file.
Was this helpful? Thank you for your feedback! -
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.
Check that the PC is using the correct recording device.
1. Go to Control Panel
2. Select Sound
3 Select Recording
4. Make sure to select the proper recording device.- Right-click on it Quantum headset.
- Now select "Set Default Device" or "Select Default Communication Device"
6. Go to Properties
7. Chose Levels and adjust accordinglyWas this helpful? Thank you for your feedback! -
Ensure that only one voice chat application is in use while in-game. Be sure you hear a click when the microphone is flipped down. The microphone will only function when it is flipped down fully. If you see a red LED on the microphone, it is muted.
Check that the PC is using the correct recording device.
1. Go to Control Panel
2. Select Sound
3 Select Recording
4. Make sure to select the proper recording device.- Right-click on it Quantum headset.
- Now select "Set Default Device" or "Select Default Communication Device"
6. Go to Properties
7. Choose Levels and adjust accordinglyWas this helpful? Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00
