JBL Tune 220TWS

As with all in-ear headphones, our range of True Wireless Stereo headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). This should remove the wax and resolve the volume/balance issues.

 

This headphone does not support aptX, aptX HD, aptX Low Latency audio codecs.

It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.

Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.

Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.

Repeat until the contact points are visibly clean, and charging should work as designed.

Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
This procedure can be performed on all True Wireless Stereo earphones and cases.

If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.

• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.

• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.

• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.

• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.

• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.

Place both ear pods in the charging box, while the charging box is plugged into a power source. Press and hold the button on the Right pod for about 5 seconds. The LED on the pod will turn off and then turn back on again. This restores to factory defaults. (Please note that charging must take place for reset to work.) It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.

1. Put the earbuds back into the charging case and close the lid. 2. Press and hold the buttons on both the left and right earbuds for more than 2 seconds. Alternatively, only press and hold one of the buttons to just turn off the left or right earbud as required. 3. Use the Auto-off function via the JBL Headphone app (Only applicable for headphones supported in our JBL Headphone app).

This headphone does not feature volume control. You must manually control volume from your device.

If the left ear pod is silent, please perform a new pairing with the right pod like shown in the quick-start guide.
Take them out of the charging case and click the  center button on both the left and the right pod 3 times.
This forces a new pairing between the pods, and the left pod should automatically pair with the right pod from now on once you remove both pods from the charging case.

If you still cannot get the Left ear to play, please perform a factory reset by placing both pods in the charging case, while the charging case is charging. Now press the button on the right pod, and hold it for more than 5 seconds. You have now reset to factory settings. (Please note: If you have performed a factory reset, you will need to remove the headphones or "forget this device" from any smart phone or tablet they were once connected to. This will allow your device to now search for the newly restored headphones under BT devices)


The right pod is the primary, which is connected to your source, usually a smartphone.
The left pod is the secondary, which connects to the right pod.
 

The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.

1. Forget/unpair the headphones on your device.
2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
3. Pair the headphones to your device and see if this resolves the problem.
4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
   • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
   • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
   • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
   • Pair the buds to your Source Device.