


JBL Tune 720BT
Med JBL Tune 720BT-hovedtelefonerne kan du trådløst afspille kraftfuld JBL Pure Bass-lyd takket være den nyeste Bluetooth 5.3-teknologi. Disse hovedtelefoner er nemme at bruge og giver dig op til 76 timers ren nydelse og 3 ekstra timers batteritid efter kun 5 minutters opladning. Hent den gratis JBL Headphones-app, og tilpas din lyd via EQ, mens stemmemeddelelser guider dig gennem hovedtelefonernes funktioner. Håndter opkald, lyd og lydstyrke fra ørekoppen takket være den praktiske knapstyring. Hvis du får et opkald, mens du ser en video på en anden enhed, skifter JBL Tune 720BT problemfrit til din mobil, så du aldrig går glip af et opkald. JBL Tune 720BT-hovedtelefonerne er lette og komfortable, selv efter mange timers lytning. De kan foldes fladt sammen i din rygsæk, så de følger dig overalt.
Product Specifications
General Specifications
Enheds-størrelser (mm) | 40 |
---|---|
Number of Microphones | 1 |
Audio Specifications
Enheds-følsomhed ved 1kHz/1mW (dB) | 101 |
---|---|
Dynamisk frekvensområde (Hz) | 20 Hz – 20 kHz |
Impedans (ohm) | 32 |
Dimension Specifications
Ear Cup External Height (in) | 2.8 |
---|---|
Ear Cup External Width (in) | 2.8 |
Ear Cup Internal Height (in) | 3.6 |
Ear Cup Internal Width (in) | 3 |
Ear Cup Depth (in) | 1.9 |
Højde (cm) | 7 |
Bredde (cm) | 7 |
Indre bredde (cm) | 9.3 |
Indre højde (cm) | 7.6 |
Dybde (cm) | 4.8 |
Control Connect Specifications
Bluetooth-version | 5.3 |
---|---|
Bluetooth-profiler | HFP v1.7.2, AVRCP v1.6.2, A2DP v1.3.2 |
Bluetooth-frekvens | 2.4 GHz – 2.4835 GHz |
Bluetooth sender-modulation | GFSK, π/4-DQPSK, 8-DPSK |
Bluetooth sender-effekt | ≤ 10 dBm (E.I.R.P) |
Documents & Downloads
Gallery












What’s in the Box
- 1 x JBL Tune 720BT-hovedtelefoner
- 1 x USB-C-ladekabel
- 1 x aftageligt lydkabel
- 1 x garanti / advarselsark
- 1 x startguide

FAQs & How-Tos
Can my headphones be connected to two devices simultaneously?
Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices.
Was this helpful?
Thank you for your feedback!
How can I reset the headphones?
Press volume + and volume - simultaneously for 5 seconds to reset.
The headphone must be ON while doing this.
The headphone must be ON while doing this.
Was this helpful?
Thank you for your feedback!
My JBL Headphones App Support
This headphone is supported by the My JBL Headphones App.
Was this helpful?
Thank you for your feedback!
Multi-Point Connection Support
This product features Multi-Point Connection which allows you to be connect to two devices at the same time. Effortlessly switch from listening to music on your portable device to a call from your phone.
To connect to two devices at the same time:
1. Power on your product.
2. Make sure that the device you wish to connect to has the BT settings on and within range.
3. If this is the first time connecting your product, you will notice a flashing LED to indicate that it is searching for a device to connect to. (If this is not your first time, your product will automatically reconnect to the last device it was connected to)
4. Under your BT settings, go to discoverable devices and the product name should pop up within a few seconds. Depending on the device you are using, you may have to tap on the product to complete the connection.
5.Now that you are connected to the first device, push the BT button on the product to connect to the second device. The product should start searching for the second device by displaying a flashing LED.
6. Go to your BT settings on your second device. The product should pop up on your discoverable devices should pop up within a few moments.
(Please Note: If the product does not show up on your discoverable devices while it is in pairing mode, quickly turn off your BT settings and turn it back on. This will typically result in resetting the BT search in which your product should pop up on discoverable devices within a few moments)
To connect to two devices at the same time:
1. Power on your product.
2. Make sure that the device you wish to connect to has the BT settings on and within range.
3. If this is the first time connecting your product, you will notice a flashing LED to indicate that it is searching for a device to connect to. (If this is not your first time, your product will automatically reconnect to the last device it was connected to)
4. Under your BT settings, go to discoverable devices and the product name should pop up within a few seconds. Depending on the device you are using, you may have to tap on the product to complete the connection.
5.Now that you are connected to the first device, push the BT button on the product to connect to the second device. The product should start searching for the second device by displaying a flashing LED.
6. Go to your BT settings on your second device. The product should pop up on your discoverable devices should pop up within a few moments.
(Please Note: If the product does not show up on your discoverable devices while it is in pairing mode, quickly turn off your BT settings and turn it back on. This will typically result in resetting the BT search in which your product should pop up on discoverable devices within a few moments)
Was this helpful?
Thank you for your feedback!
How to avoid Bluetooth Interference or Interruptions
• Always have clear line of sight between your Bluetooth device (speaker, headphones etc.) and source device (Smartphone/tablet/PC etc). Be aware of obstacles in front of your devices.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.
• Try to shutdown other products that have Bluetooth, but are not being used. They are often the reason for interference even though they are not being used.
• Do not stand too close to your Wi-Fi router since a Wi-Fi signal is stronger and in many cases will "overlap" the connection.
• Be aware of walls around you. Concrete and brick walls will often interrupt the signal, as it cannot pass through such thick walls.
• Bluetooth signals cannot travel through water, which includes the human body. Make sure with wireless headphones to keep your source device and the receiver on the same side of your body.
• Open spaces such as parks can cause issues for your devices, as open air is "bad" for any Bluetooth signal if it cannot reflect from objects around you.
Was this helpful?
Thank you for your feedback!
Pairing issues with a Smartphone or Tablet
1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.
3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.
4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.
5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.
6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.
You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
Was this helpful?
Thank you for your feedback!
How to connect your headphones to the Google Assistant for iOS devices
Visit your App store to download the ‘Google Assistant’ App.
After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.
Follow the steps to connect and pair “JBL XXXX-LE” with the Google Assistant App, the name will depend on your model.
Once set up is complete, you will see the below screen:
PLEASE NOTE: To verbally interact with your Google Assistant via the headphone, you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.

After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.
Step 1

Follow the steps to connect and pair “JBL XXXX-LE” with the Google Assistant App, the name will depend on your model.
Once set up is complete, you will see the below screen:
Step 2

PLEASE NOTE: To verbally interact with your Google Assistant via the headphone, you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.


Was this helpful?
Thank you for your feedback!
How to connect your headphones to the Google Assistant for Android devices
If not pre-installed on your Android device, visit your App store to download the ‘Google Assistant’ App.
After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.
Follow the steps to connect and pair “JBL XXXX-LE” (depends on your model) with your devices.
Once set up is complete, you will see the below screen:
PLEASE NOTE: In order to verbally interact with your Google Assistant via the headphone you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under: Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.

After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.
Step 1

Follow the steps to connect and pair “JBL XXXX-LE” (depends on your model) with your devices.
Once set up is complete, you will see the below screen:
Step 2

PLEASE NOTE: In order to verbally interact with your Google Assistant via the headphone you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under: Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.


Was this helpful?
Thank you for your feedback!
Can’t find what you’re looking for?
Chat with us
Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00