Bluetooth / Wireless

  • Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
    How can I reset the headphones?
    Press volume + and volume - simultaneously for 5 seconds to reset.
    The headphone must be ON while doing this.
    More FAQs
  • Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
    How can I reset the headphones?
    Press volume + and volume - simultaneously for 5 seconds to reset.
    The headphone must be ON while doing this.
    How to connect your headphones to the Google Assistant for iOS devices
    Visit your App store to download the ‘Google Assistant’ App.

    After you have paired your JBL headphones to your device via Bluetooth, you should receive a pop-up notification (pictured below). Please tap the notification on your device to start the Google Assistant setup. You will now be directed to the Google Assistant App.

    Step 1

      Set up Google Assistant #1.png
    Follow the steps to connect and pair “JBL XXXX-LE” with the Google Assistant App, the name will depend on your model.
    Once set up is complete, you will see the below screen:

    Step 2

    Set up Google Assistant #2.png

    PLEASE NOTE: To verbally interact with your Google Assistant via the headphone, you must turn on the ‘Spoken Notifications’ in the Google Assistant App. This can be found under Assistant Devices > Notifications. Alternatively, your JBL headphones can be added to the Google Assistant App manually by adding them as a Bluetooth device if this was not done when first paired. Google Assistant must be selected as your chosen voice assistant in the settings of the My JBL Headphones App also.
      Set up Google Assistant #3.png
    Set up Google Assistant #4.png
    More FAQs
  • How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
  • Differences between True Adaptive Noise Cancelling and Adaptive Noise Cancelling

    The True Adaptive Noise Cancelling technology is a features which adjusts noise-cancelling levels in real-time, 50,000 times per second to account for environmental ambient noises and personal attributes such as movement, hair and eyeglasses to deliver best-in-class Noise Cancelling and immersive sound in any environment.  
    With the help of Feed Forward and Feed Backward microphones, the Adaptive Noise Cancelling technology fully monitors exterior sounds picking up low-frequencies and neutralizing them before they reach the ear. The headphones generate a sound that's phase-inverted by 180 degrees to the unwanted noise, resulting in the two sounds cancelling each other out. 
    In addition, all headphones allow the listener to adapt or adjust the level of ambient noise through features like Ambient Aware and TalkThru.

    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
    What can I do with the JBL Tour Pro 2 Smart Case?

    The JBL Tour Pro 2 allows you to find your preferred control method in any scenario. When you want to control your headphones, you no longer need to take your phone out, open the JBL Headphones app and wait for the headphones to connect in the app. All features are accessible directly on the Smart Case, where you can easily select any key feature, you know from the app.

    Some of the features you can access on the Smart Case includes playing and pausing your music, skip to the next/previous track, volume adjustment, answer/reject calls, customize the EQ settings, Spatial audio, ANC and Ambient Sound Control, timer & clock, receive notifications, screensavers, and a battery indicator. 

    How do I start the JBL Tour Pro 2 for the first time?

    The JBL Tour Pro 2 is in a deep sleep mode, which it is to prolong the lifetime of the battery. Connect the case to a charger for about 2 seconds to wake the product up and take the earbuds out from the case. Once you put the earbuds back in the case, it's ready to pair through Bluetooth. 

    More FAQs
  • Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    JBL Headphones App: Personal Sound Amplification (PSAP)

    PSAP (Personal Sound Amplification) is a new feature accessible within the JBL Headphones App. When this feature is turned on, it works similar to Ambient Aware, but it focuses on picking up vocal frequencies in front of you. 

     

    1. GAIN: The Personal Sound Amplification function is designed to amplify sound in the vocal range, it can assist users with (limited) hearing loss to maintain conversations more easily, especially in noisy environments. It should then amplify the speech of the person sitting across from you, not the general ambient sound as with Ambient Aware. The algorithm uses beamforming to pick out the voice from the other sounds, much like what happens during a phone call, but instead of focusing on your own voice it focuses on the voice further away from you. The gain setting allows you to amplify those vocal frequencies.

     

    2. BALANCE: The balance setting adjusts the amplification effect between your left and right ears using the slider. When set to 0 (in the middle), both ears will receive the same amplification, but depending on the user’s personal needs/preferences, they can focus the amplification more towards either the left or right ear. 

     

    PSAP pics.PNG
    Differences between True Adaptive Noise Cancelling and Adaptive Noise Cancelling

    The True Adaptive Noise Cancelling technology is a features which adjusts noise-cancelling levels in real-time, 50,000 times per second to account for environmental ambient noises and personal attributes such as movement, hair and eyeglasses to deliver best-in-class Noise Cancelling and immersive sound in any environment.  
    With the help of Feed Forward and Feed Backward microphones, the Adaptive Noise Cancelling technology fully monitors exterior sounds picking up low-frequencies and neutralizing them before they reach the ear. The headphones generate a sound that's phase-inverted by 180 degrees to the unwanted noise, resulting in the two sounds cancelling each other out. 
    In addition, all headphones allow the listener to adapt or adjust the level of ambient noise through features like Ambient Aware and TalkThru.

    More FAQs
  • Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
  • How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
  • TUNE FLEX: Software Update Release Notes
    TUNE FLEX
    Software Update Release Notes
    ------------------------------------------------------------------------
    Software Version:  V3.1.0 (global)
    Release Date:  September 14, 2022
    Release Media:  OTA (over the air) via JBL Headphone App


    What’s New
    1. Improved the connectivity between left and right earbud.
    2. ANC (active noise cancelling) can be activated more quickly.
    3. Optimized the APP user experience for better flow.
    Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    My JBL Headphones App Support
    This headphone is supported by the My JBL Headphones App.
    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
    More FAQs
  • How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
    IP68 Information
    This unit is fully dust-proof, and can withstand continuous immersion in water (up to 1.5 meters / 4.9ft for 30 minutes). 
  • Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
    LIVE FREE 2 TWS: Software Update Release Notes
    LIVE FREE 2 TWS
    Software Update Release Notes
    ------------------------------------------------------------------------
    Software Version:  V6.9.8
    Version (iOS):  V5.7.9
    Version (Android):  V5.7.9
    Release Date:  July 8, 2022
    Release Media:  OTA via JBL Headphone App


    What’s New
    1. Added Microsoft Swift Pairing feature.
    2. Fixed a few minor software bugs for better user experience.
    More FAQs
  • How to use Amazon Alexa with your headphones
    After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
      Trigger Alexa #2 FAQ.png

    Things to try
    • “What’s the weather?”
    • Play Niall Horan
    • Play NPR on iHeartRadio
    • Set a timer for 5 minutes
    • What new skills do you have?
    Stop Alexa when she talks
    While Alexa is talking, press and release the Action button then say “Stop”.

    For more information and things to try with Alexa, visit: www.amazon.com/alexadevices
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    How to use Google Assistant with your headphones
    After setting up Google Assistant on your headphones through the My JBL Headphones app, use Google Assistant by pressing & holding the touch panel for 2 seconds on the earbud that you enabled the voice assistant feature on.
    Trigger Google - #1 FAQ.png
    Press and hold the Action button to begin. Requires pairing with eligible phone and internet connection. For examples of questions and things you can do, visit: https://assistant.google.com/platforms/phones/#headphones

    Get your notifications
    Double-tap the Action button.

    Stop your Google Assistant
    Touch the Action button.

    Reply to the message (where available)
    After receiving a message notification, touch and hold the Action button to respond. When you’re done, release the button.

    For more information on what your Google Assistant can do, visit: https://assistant.google.com/platforms/headphones

     
    More FAQs
  • Re-establishing Volume Levels/Balance between Earbuds and charging
    As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

    If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

    cleaning-earstick-tip 
    Sweatproof Information (IPX4)
    This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

    Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    More FAQs
  • TWS Left & Right Not Pairing Together
    The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.
    1. Forget/unpair the headphones on your device.
    2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
    3. Pair the headphones to your device and see if this resolves the problem.
    4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
    5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
      • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
      • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
      • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
      • Pair the buds to your Source Device.
    Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    More FAQs
  • Re-establishing Volume Levels/Balance between Earbuds and charging
    As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

    If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

    cleaning-earstick-tip 
    TWS Left & Right Not Pairing Together
    The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.
    1. Forget/unpair the headphones on your device.
    2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
    3. Pair the headphones to your device and see if this resolves the problem.
    4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
    5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
      • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
      • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
      • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
      • Pair the buds to your Source Device.
    Sweatproof Information (IPX4)
    This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

    Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    More FAQs
  • Re-establishing Volume Levels/Balance between Earbuds and charging
    As with all in-ear headphones, our range of TWS headphones can be susceptible to a build up of dust and earwax. This can cause low volume on one or both earbuds, or balance issues (e.g. right earbud is louder than the left earbud). To reduce the likelihood of these issues occurring, it is a good idea to periodically clean your earbuds. Clean the earbuds by removing dust and wax after each use, using a pointed toothpick to remove larger amounts and a small amount of rubbing alcohol applied to a cotton swab for final degreasing. Remember to clean the charging points on the headphones and inside the charging case.

    If you are experiencing volume or balance issues, always check for wax and dirt in and around the earbud and driver and complete cleaning of the earbuds as described above. If the issue persists, there may be earwax/dirt stuck in the small holes in the grille in front of the driver, preventing sound output. To resolve the issue try dipping the affected earbud tip into a solution of lukewarm tap water and a small amount of dish soap (washing up liquid). The earbud tip should only be put into the liquid up to a maximum depth of 1-2 mm only (see images below). Immersing the earbuds in water or putting the earbuds in water at a larger depth than this could void your warranty. Keep the earbud tip in the water for about 2-3 minutes, then wipe/clean the grille with a small brush (such as a toothbrush). The should remove the wax and resolve the volume/balance issues.

    cleaning-earstick-tip 
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
  • TWS Left & Right Not Pairing Together
    The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.
    1. Forget/unpair the headphones on your device.
    2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
    3. Pair the headphones to your device and see if this resolves the problem.
    4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
    5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
      • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
      • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
      • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
      • Pair the buds to your Source Device.
    Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    More FAQs
  • Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
  • How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
  • TWS Left & Right Not Pairing Together
    The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.
    1. Forget/unpair the headphones on your device.
    2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
    3. Pair the headphones to your device and see if this resolves the problem.
    4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
    5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
      • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
      • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
      • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
      • Pair the buds to your Source Device.
    Cleaning Instructions for Re-establishing Charging
    It is not uncommon to have charging problems with True Wireless headphones. You may encounter that charging stops, does not start at all or that one of the ear buds suddenly switches on and begins the pairing process. This is almost always caused by dirt on the metal charging contacts. These contacts are vulnerable because they can easily be contaminated by sweat, skin grease, or ear wax. They are usually gold plated, but gold plating does not prevent surface dirt.

    If you have charging problems, the first step is to always clean all contact points, on each earbud and on the charging case.
    You will need: cotton cloth or makeup swab, cotton swabs and rubbing alcohol. Also a pencil with eraser for further cleaning.
    needed-tools.png
    Use a cotton swab with some rubbing alcohol to clean the charging terminals of the headphones. Rotate the swab and scrub lightly on each contact surface, then use a cotton cloth to remove any dust and cotton residue left on the headphones. It is important to perform this process periodically to keep your headphones clean, thus avoiding affecting the charging speed/quality.
    cleaning-earbud-contact-points.png
    Wipe the contact pins in the charging case with a clean cotton swab. The swab can be slightly moistened with rubbing alcohol, but it is important that the interior is completely dry before closing the box. Use the cotton cloth and wait for it to dry.
    cleaning-charging-case.png
    Repeat until the contact points are visibly clean, and charging should work as designed.

    Try cleaning the contacts with the tip of a pencil and the eraser at the end of the pencil, the graphite and rubber can help to re-establish charging also.
    This procedure can be performed on all TWS earphones and cases.
    Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    How to Factory Reset True Wireless Stereo Earbuds
    Double-tap the button on the right earbud, then on the third tap - press and hold the button for more than 5 seconds (until the unit shuts off). 
    This restores the earbuds to the factory defaults.
    TWS must be connected to perform the reset, so neither of the earbuds should be off or in the charging case.
    It also may be necessary to remove or forget the earbuds from the list of paired Bluetooth devices in order to pair again.
    More FAQs
  • Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    More FAQs
  • TWS Left & Right Not Pairing Together
    The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.
    1. Forget/unpair the headphones on your device.
    2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
    3. Pair the headphones to your device and see if this resolves the problem.
    4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
    5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
      • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
      • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
      • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
      • Pair the buds to your Source Device.
    SilentNow and My Alarm Feature
    The JBL TOUR range helps you create an ideal world where you can entirely focus on your tasks.
    With the JBL Tour One and Tour Pro+ TWS, you can get silent moments with SilentNow. Noise Cancelling is activated without Bluetooth, just by pressing a dedicated button on the headphones (or tapping the earbud) or controlling via the My JBL Headphones app. It also helps you save battery time.
    Or get help in waking up with My Alarm, which allows sleep and wake times to be set and is controlled ​via the My JBL Headphones app. You can set a sleep and wake timer to gradually lower the volume of the headphones for sleep, switch into SilentNow mode for a specific amount of time and then wake you up at a specified time.

      Sleep now.png Sleep now 2.png Sleep now #3.png
    How to use Amazon Alexa with your headphones
    After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
      Trigger Alexa #2 FAQ.png

    Things to try
    • “What’s the weather?”
    • Play Niall Horan
    • Play NPR on iHeartRadio
    • Set a timer for 5 minutes
    • What new skills do you have?
    Stop Alexa when she talks
    While Alexa is talking, press and release the Action button then say “Stop”.

    For more information and things to try with Alexa, visit: www.amazon.com/alexadevices
    Sweatproof Information (IPX4)
    This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

    More FAQs
  • SilentNow and My Alarm Feature
    The JBL TOUR range helps you create an ideal world where you can entirely focus on your tasks.
    With the JBL Tour One and Tour Pro+ TWS, you can get silent moments with SilentNow. Noise Cancelling is activated without Bluetooth, just by pressing a dedicated button on the headphones (or tapping the earbud) or controlling via the My JBL Headphones app. It also helps you save battery time.
    Or get help in waking up with My Alarm, which allows sleep and wake times to be set and is controlled ​via the My JBL Headphones app. You can set a sleep and wake timer to gradually lower the volume of the headphones for sleep, switch into SilentNow mode for a specific amount of time and then wake you up at a specified time.

      Sleep now.png Sleep now 2.png Sleep now #3.png
    How to use Amazon Alexa with your headphones
    After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
      Trigger Alexa #2 FAQ.png

    Things to try
    • “What’s the weather?”
    • Play Niall Horan
    • Play NPR on iHeartRadio
    • Set a timer for 5 minutes
    • What new skills do you have?
    Stop Alexa when she talks
    While Alexa is talking, press and release the Action button then say “Stop”.

    For more information and things to try with Alexa, visit: www.amazon.com/alexadevices
    The Noise Cancellation we are using in our JBL TOUR Series
    True Adaptive NC available on Tour One enables real-time monitoring of exterior surroundings and personal attributes like movement, hair, eyeglasses, and automatic adjustments to the NC performance and EQ.

    If you don’t prefer the canceling performance's automatic change, you can get a fine-tuned canceling level by choosing “Everyday Mode” in the app.


    Adaptive Noise Cancelling - available on Tour Pro+ TWS - listens to ambient environmental noises using external and internal mics then creates the inverse phase back to the listener creating the noise “canceling” effect.
    The headphones also allow the listener to adapt or adjust noise cancellation through features like Ambient Aware and TalkThru.
    How to connect your headphones to the Amazon Alexa for Android and iOS devices
    Visit the App Store and download the ‘Amazon Alexa’ App.

      Set up Amazon Alexa #1.png
    1. Click the Plus(+) button on the top right of the screen.
    2. Then select ‘Add Device‘.
    3. Select headphones from the list and then choose your Headphones from the list of available devices.
    4. Follow the rest of the instructions in the Alexa App to complete the setup.
    More FAQs
  • How to use Amazon Alexa with your headphones
    After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
      Trigger Alexa #2 FAQ.png

    Things to try
    • “What’s the weather?”
    • Play Niall Horan
    • Play NPR on iHeartRadio
    • Set a timer for 5 minutes
    • What new skills do you have?
    Stop Alexa when she talks
    While Alexa is talking, press and release the Action button then say “Stop”.

    For more information and things to try with Alexa, visit: www.amazon.com/alexadevices
    How to connect your headphones to the Amazon Alexa for Android and iOS devices
    Visit the App Store and download the ‘Amazon Alexa’ App.

      Set up Amazon Alexa #1.png
    1. Click the Plus(+) button on the top right of the screen.
    2. Then select ‘Add Device‘.
    3. Select headphones from the list and then choose your Headphones from the list of available devices.
    4. Follow the rest of the instructions in the Alexa App to complete the setup.
    Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    More FAQs
  • Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    More FAQs
  • TWS Left & Right Not Pairing Together
    The two earpieces of your TWS headphones should normally be connected together without issue.  However, if they are no longer paired to each other, please follow these steps, in order.
    1. Forget/unpair the headphones on your device.
    2. Manually pair the two earpieces together following the "Manual Pairing Left & Right" instructions in your Owner's Manual/Quick Start Guide.
    3. Pair the headphones to your device and see if this resolves the problem.
    4. If manual pairing does not fix the problem, forget/unpair the headphones on your device again.
    5. Initiate a Product Reset to reset the earbud’s Bluetooth connection.
      • Note that RESET will wipe all previous settings and pairings, so it will be necessary to pair your headphones with your devices again
      • Follow the Product Reset instructions in your Owner's Manual/Quick Start Guide.
      • Manually pair the 2 buds together again, as you did in step 2.  This additional step is necessary because, by default, the reset procedure does not automatically pair the two ear pieces together, but it does wipe all previous settings and resets the internal processor, so it is necessary to manually pair the two ear pieces together again.
      • Pair the buds to your Source Device.
    How to use Amazon Alexa with your headphones
    After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
      Trigger Alexa #2 FAQ.png

    Things to try
    • “What’s the weather?”
    • Play Niall Horan
    • Play NPR on iHeartRadio
    • Set a timer for 5 minutes
    • What new skills do you have?
    Stop Alexa when she talks
    While Alexa is talking, press and release the Action button then say “Stop”.

    For more information and things to try with Alexa, visit: www.amazon.com/alexadevices
    Sweatproof Information (IPX4)
    This unit is IPX4 rated, which means that it is sweatproof (suitable for working out) and can withstand water splashes from any direction. However, the unit is not waterproof and should never be submerged in water.

    How to connect your headphones to the Amazon Alexa for Android and iOS devices
    Visit the App Store and download the ‘Amazon Alexa’ App.

      Set up Amazon Alexa #1.png
    1. Click the Plus(+) button on the top right of the screen.
    2. Then select ‘Add Device‘.
    3. Select headphones from the list and then choose your Headphones from the list of available devices.
    4. Follow the rest of the instructions in the Alexa App to complete the setup.
    More FAQs
  • Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 
    Headphones & Third Party Communication Apps (Skype, Zoom, WhatsApp, etc)

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    If you are experiencing issues getting the app to communicate with your headphones, (assuming you have already paired the headphones with the device) go into the communication apps audio settings. You will likely find the resolution there. You may have to set your headphones as the ‘communication device’ within the app you are using. 

    More FAQs
  • How to use Amazon Alexa with your headphones
    After setting up Amazon Alexa on your headphones through the My JBL Headphones app, use Amazon Alexa by pressing & holding the touch panel for 2 seconds on the earbud that you have enabled the voice assistant feature on.
      Trigger Alexa #2 FAQ.png

    Things to try
    • “What’s the weather?”
    • Play Niall Horan
    • Play NPR on iHeartRadio
    • Set a timer for 5 minutes
    • What new skills do you have?
    Stop Alexa when she talks
    While Alexa is talking, press and release the Action button then say “Stop”.

    For more information and things to try with Alexa, visit: www.amazon.com/alexadevices
    How to connect your headphones to the Amazon Alexa for Android and iOS devices
    Visit the App Store and download the ‘Amazon Alexa’ App.

      Set up Amazon Alexa #1.png
    1. Click the Plus(+) button on the top right of the screen.
    2. Then select ‘Add Device‘.
    3. Select headphones from the list and then choose your Headphones from the list of available devices.
    4. Follow the rest of the instructions in the Alexa App to complete the setup.
    Pairing issues with a Smartphone or Tablet
    1. First, try to restart the Bluetooth connection on your source device (Smartphone/tablet/PC) by switching Bluetooth off and on again with a short pause in between.

    2. "Forget" (remove) the previously paired connection (on your smartphone/tablet/PC) in your Bluetooth settings if you had once paired with your product.

    3. Try to restart the source device (Smartphone/tablet/PC) by powering it off and on again and after restarting, try to establish a Bluetooth connection to your product.

    4. If the above does not work, then try to restart your product (Portable speaker, Headphone) by turning it off and on again.

    5. Press and hold down the Bluetooth button on your device (Portable speaker, Headphones) to initiate pairing mode again.

    6. Go into the Bluetooth settings on your Smartphone/tablet or PC to start the pairing process.

    You should now have a successful pairing with your device. If you are still experiencing issues, please contact us again.
    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    More FAQs
  • Firmware Information - JBL Firmware Update App

    If you are experiencing issues with your headphones' Bluetooth disconnecting and reconnecting while on standby, there is a new Firmware Update app to resolve this issue. Start by downloading the app  "JBL Firmware Update" (see links below).
    Google Play Store:
    https://play.google.com/store/apps/details?id=com.jbl.tune.update
    App Store: https://apps.apple.com/gb/app/jbl-firmware-update/id1548227663

    Once downloaded, you can update your headphones firmware from there. 
    Below you can see step by step images of the update process.


    Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg Screenshot_JBL FW Update-01.jpg 

    Voice Assistant Headphone Connection
    If you are having trouble pairing your headphones or if your device is asking for a PIN, please make sure to check all available BT connections in your device's settings. Verify that you are connecting to the headphone's product name that excludes 'LE'. The 'LE' connection is only intended for voice assistant feature compatible with your headphones. If the voice assistant feature has not yet been configured, this would explain why the 'LE' connection appears as an available connection, but cannot be used for Bluetooth audio.

    https://harman.widen.net/s/dtsldx6jxx/bluetooth-pairing-issue-with-voice-assistant-headphone-le-image1 
    Can my headphones be connected to two devices simultaneously?
    Yes, the headphones have Multipoint Connection, which allows you to switch seamlessly between the connected devices. 

Further Support

Bluetooth Guide

Har du brug for hjælp til Bluetooth parring? Denne guide kan hjælpe dig

Lær mere

Reset Guide

Skal du have hjælp til at resette dit produkt? Her kan du finde instruktionerne

Lær mere

Headphone Support Guide

Need help to resolve some the most common headphone challenges?

Learn more

Gaming Support

Need help with your JBL Quantum? Check out the Quantum support page!

Go to Quantum Support!

Order Status

Do you need to check the status of your order?

Check an order

Accessories

Looking for an accessory?

Learn more

Can’t find what you’re looking for?

Call us

Call us

Call us now at: +45 32712498

Monday - Friday: 09:00 - 17:00

E-mail us

E-mail us

We are here Monday – Sunday to answer you as fast as we can!

Email us
Chat with us

Chat with us

Monday - Friday: 09.00-18.00
Saturday - Sunday: 10:00-16:00