MS-A5001

MS-A5001

500-watt, Class D subwoofer amplifier

Sold from 2010 until now

Made in: China

Documents & Downloads

Product Specifications

Series
MS Series
Type
Mono / Subwoofer
Signal-to-Noise Ratio
80dB
2-Ohm Power Output
500W RMS x 1 channel @ 2 ohms
4-Ohm Power Output
500W RMS x 1 channel @ 4 ohms
Remote Bass-Level Control Included
Not Included
Input Sensitivity
100mV
Frequency Response
20-270Hz
Height (in)
2-3/4
Width (in)
8-1/4
Depth (in)
7-3/4
Height (mm)
70
Depth (mm)
183
Width (mm)
210

Harness the DSP control and Class D low-frequency power

The JBL® MS-A5001 digital subwoofer amplifier proves that serious power really can come in a modestly sized package. Through leading-edge electronic and industrial design, JBL engineers have created an iconic-looking, small-footprint, Class D full-range amplifier featuring a digital input mixer that provides precise audio-signal control by leveraging the power of an onboard digital signal processing (DSP) engine. The DSP controls all output levels and active crossover attributes (including relative channel levels, slope, filter point and bandwidth) to exacting tolerances. The unit’s CEA®-2006 rated power is delivered at 500 watts into 4 or 2 ohms through easy-connect, dual-speaker output terminals accepting up to 10AWG wire. There are full-range, pass-through RCA audio outputs to connect additional amplifiers such as the companion MS-A1004 four-channel model. Professional-quality amplifier configuration and setup is easily completed with the included CD, the intuitive user controls and the bright, easy-to-read display on the top of the amplifier.

The MS-A5001 is a powerful, efficient, premium Class D subwoofer amplifier. Class D topology means lower current draw and operating temperatures, which translate into greater efficiency in delivering high-quality sound. At 500 watts into 4 or 2 ohms (fully CEA-2006 compliant), it has the output to drive one or more subwoofers with powerful impact, all while having minimal effects on your vehicle’s electrical system.
The MS-A5001 leverages the power of digital signal processing (DSP) with its unique input mixer. All output-level settings, channel assignments and active crossover functions are handled through this powerful DSP engine to highly accurate tolerances. Should power be disconnected or lost, the unit will retain all of your settings in a non-volatile memory. And DSP technology, found in many high-end signal processors, is built right in.
The MS-A5001 provides top-panel control via a combination LED display and rotary-encoder control with just two navigation buttons. All necessary setup processes are aided with a menu-driven CD that’s included with the unit. Once you set up the unit, you need never worry about the controls being pushed or tweaked, since all settings remain in the unit’s memory even when the power is disconnected.
The MS-A5001’s digital input mixer features 97 individual crossover settings between 20Hz and 20kHz, for either low- or high-pass (as a subsonic filter) configuration, to match the needs of the subwoofer enclosure and audio-system configuration precisely. In addition, the unit lets you select three different orders of response (roll-off): 6, 12 or 24 decibels/octave.
JBL engineers have built the MS-A5001 for complete compatibility with any OEM (original-equipment manufacturer) audio system. The unit accepts input-signal voltages of up to 20 volts (Speaker wire-to-RCA adapters are included.) It can turn on with a wired input ranging from +5 volts DC to the standard +12 volts DC, allowing more flexibility with low-voltage turn-on circuits. If there is no turn-on circuit, programmable signal sensing can turn the unit on whenever an audio signal is present.
Setting and matching the input levels of the MS-A5001 is an easy and precise exercise with the help of the included setup CD. After you connect and configure the inputs, simply feed the amplifier an input signal and raise the signal source level to its maximum (undistorted) output volume. Then adjust the input controls until the checkmark icon is displayed to indicate that the unit has reached its optimum setting.
The MS-A5001 includes a set of pass-through, pre-amp level RCA outputs that are unaffected by the input mixer so that you can add amplifiers without using splitters or Y-adapters. It’s an efficient way to provide system expansion flexibility without having to run additional cables or make any additional connections.
The MS-A5001 amplifier features robust connection terminals for power, ground, remote turn-on and speakers. The power/ground terminals accept up to 4AWG wire. (We recommend a minimum of 8AWG.) Speaker terminals for each channel pair accept up to 10AWG wire are paralleled to allow multiple subwoofers to connect in a clean and manageable way.
The MS-A5001 has a modest footprint that allows you to install the unit just about anywhere. At 7-3/16 x 8-1/4 inches (183 x 210 millimetres), the mounting area is small enough to work in any vehicle without compromising space. With a height of only 2-3/4 inches (70 millimetres), the amplifier has plenty of clearance to fit under seats, behind panels or in other locations.
The MS-A5001 is compatible with the JBL MS-WBC wireless bass control, which provides shelving bass boost up to 10 decibels at the amplifier without making you connect any additional wires. Its unique shelving-boost functionality lets you add linear boost below 60Hz without affecting its low-pass crossover frequency. You can buy the MS-WBC separately and install it in just about any location within reach of the driver.

Can’t find what you’re looking for?

Call us

Call us

Call Us now at: 877-457-2592

Monday - Friday 8:30 a.m. - 5:30 p.m. (ET)

E-mail us

E-mail us

We are here Monday – Friday to answer you as fast as we can!

Email us