P8662

P8662

225-watt, two-way, 6" x 8" speakers

Verkocht vanaf 2008 tot nu

Voorganger product: POWER P8652
Gemaakt in: China

Aan de slag met uw P8662

Product Registration

Registreer uw product

Bent u eigenaar van dit product? Registreer het hier! En claim eenvoudig uw garantie of service

Registreer nu

Downloads

Product Specificaties

Size
5 x 7
Series
Power Series
Type
Two-Way
Power Handling (Peak)
225W
Sensitivity
(2.83V@1m) 92dB
Power Handling (RMS)
75W
Frequency Response
40Hz – 23kHz
Nominal Impedance
2 ohms
Mounting Depth (in)
2-5/16
Mounting Depth (mm)
59.3
Mounting Cutout Diameter (in)
7-3/16
Mounting Cutout Diameter (mm)
182.4

6 inch x 8 inch / 5 inch x 7 inch 2-Way Loudspeaker with Plus One HCL woofer cone and high-bandwidth edge-driven textile dome tweeter

The Plus One® Honeycomb-Laminate™ woofer cone is exceptionally stiff and lightweight, with up to 25 percent more active surface area than a standard one of the same size. With a long-excursion surround, it boosts bass output and efficiency by two to three decibels compared with others.
It’s not the miniature tweeters that most other manufacturers use, but a high-bandwidth, edge-driven textile-dome tweeter like those found in very high-end home audio loudspeakers. Crank it up. You get less distortion at even high volumes and superior integration with the midwoofer.
Another JBL® feat of engineering: the tweeter is mounted on a 15-degree angle so you can rotate it nearly 360 degrees to aim it at the listening position for improved high-frequency response
The JBL® P8662 has tweeter-level control. Use the simple switch to set the tweeter output level to match your personal listening preference, or different mounting locations.
You’ll have 75 watts RMS and 225 watts peak power handing. And push them to the limit. You’ll hear true JBL® sound, with nothing under- or over-emphasized. The P8662 has a frequency response of 40Hz to 23kHz.
In addition to better sound quality, the new, proprietary, JBL-patented woofer design offers far higher SPL (sound pressure level) and better suspension symmetry for lower distortion than the previous generation.
These speakers make the best use of any amplifier by providing an optimum 2-ohm load. They use a lower-impedance voice coil than a typical speaker to extract the most power and performance possible from all amplifiers engineered to drive loads of 4 ohms or less.
Outboard crossovers are integrated into a harness connected to each speaker for easy installation. Oversized Direct-Connect terminals ensure perfect connectivity for bare speaker wires.

Kan je niet vinden wat je zoekt?

Bel onze support-afdeling

Bel onze support-afdeling

Bel ons nu op: +32 (0) 28080136

Maandag - Vrijdag: 09.00-18.00
Zaterdag - Zondag: 10:00-16:00

Stuur een email aan onze support-afdeling

Stuur een email aan onze support-afdeling

We zijn er van maandag t/m zondag om je vragen zo snel mogelijk te beantwoorden!

Stuur ons een email
Chat met onze support-afdeling

Chat met onze support-afdeling

Chat is open op werkdagen tussen 09:00 en 18:00 en van 10:00 - 16:00 in het weekend.

message

WhatsApp Ons

Stuur ons een bericht hier 

Maandag - vrijdag: 09.00-18.00
Zaterdag - Zondag: 10:00-16:00